DJI PSDK Información Del Producto página 3

Carefully read this entire document and all safe and lawful practices provided before use.
EN
CHS
使用本产品前，请仔细阅读并遵循本文及与本产品相关的所有安全与合规操作指引。
CHT
使用本產品前，請仔細閱讀並遵循本文及與本產品相關的所有安全與合規操作指南。
ご使用前に、この文書全体に目を通し、安全で合法的慣行についての説明を注意深く
JP
お読みください。
KR
본 문서를 포함하여 제공된 모든 안전 및 적법한 사용 방법을 사용 전에 주의 깊게 읽어 주십시오.
Bitte lies vor dem ersten Gebrauch dieses gesamte Dokument und alle sicheren und
DE
rechtmäßigen Praktiken sorgfältig durch.
Antes de usar el producto, lea atentamente este documento al completo y todas las prác-
ES
ticas de seguridad y legales proporcionadas.
Veuillez lire attentivement ce document dans son intégralité, ainsi que toutes les pratiques
FR
sécuritaires et légales avant l'utilisation.
Prima dell'utilizzo, leggere con attenzione l'intero documento e tutte le pratiche sicure e
IT
legali fornite.
Lees vóór gebruik dit hele document zorgvuldig door, evenals alle veilige en wettelijke
NL
praktijken.
Leia atentamente este documento na íntegra e todas as práticas seguras e legais indica-
PT
das antes de utilizar o produto.
Leia com atenção este documento por inteiro e todas as práticas seguras e legais forne-
PT-BR
cidas antes do uso.
Внимательно ознакомьтесь с данным документом и правилами техники
RU
безопасности перед использованием продукта.
EN
Installation and Usage
The PSDK Mounting Bracket (consisting of Bracket A and Bracket B) can be mounted on DJI
aircraft for installing PSDK payloads.
1. Install Bracket A on the aircraft with four M3 screws.
2. Use M1.6 and M2.0 screws to install the PSDK payload on Bracket B.
3. Slide Bracket B into Bracket A until you hear a "click" to ensure it is locked in place. Then
connect the payload to the PSDK port of the aircraft.
Note: After installation, check from the top of the aircraft to ensure that the gravity center of the
payload falls within the orthographic projection area of the PSDK Mounting Bracket.
4. To remove the payload, disconnect the cable, open the lock lever to unlock Bracket B from
Bracket A, then slide the payload out.
• Clean any sand or gravel from the slide rails of the bracket before use, otherwise Brackets
A and B may not lock firmly or may become stuck.
• Make sure the payload is securely locked in after installation. When removing the payload,
be careful not to drop and damage the payload.
• The bracket slide rails and lock lever can be used for 1000 times. A complete slide-
in and slide-out is counted as one time of use. Replace the bracket promptly in the
following situations:
（1） The bracket has been used longer than its service life of 1000 times.
（2） The painted surface of the slide rails or the lock lever is completely worn out (slight
wear is normal).
Specifications
Bracket Dimensions
Bracket Weight (excluding screws)
Payload Requirements
Supported DJI Aircraft
2
(Figure 1)
(Figure 3)
(Figure 4)
79.6×79.3×7.9 mm
14.5 g
Weight < 230 g, height < 10 cm
MATRICE TM 30 Series
(Figure 2)
TM