Adjusting The Riving Knife; Changing Tools - stayer SC2600W Manual De Instrucciones

go in smoothly until it stops.
Adjusting the angle for vertical cut at 45°(bevel
Verification
1 Release the vertical adjuster on the head by loosening
the head angle control lever (6) (key (H) required for
SC250W PRO / SC265W). For the SC250W model,
you must remove the extendible lateral support guide by
loosening the knob (14) before you can tilt the machine
Y
head.
2
Tilt the head as far right as possible (45°).
3
Check the angle using a duly calibrated angle chart or
goniometer (minimum accuracy +/- 5°), placing one side
on the cutting table and the other side on the cutting
blade. If the face of the angle chart does not fit the blade
exactly or if there is a deviation greater than +/- 20° when
using the goniometer, an adjustment must be made.
Adjustment
1
Using a goniometer (minimum accuracy +/- 5°), place
one side on the cutting table and the other side on the
Y
cutting blade.
2 Adjust the screws located on the head tilt axis (B) until
you reach a measurement of 90° / 45°

Adjusting the riving knife

The riving knife is the piece that holds the blade guard on the
upper table (18) in place.
Its function is to separate and divert the debris produced
when cutting on the upper table so that the debris does not
impact the user.
To check and adjust it, lock your machine in the down
Y
position, check the alignment of the knife with the blade and
ensure that the distance between the blade teeth and the
knife surface is 2 mm.
If not, adjust it using the knobs that hold the knife in place
(13).

CHANGING TOOLS

7.
Attention!
This operation must be carried out with the machine
unplugged and with the disk still. Use protective gloves.
- Use obligatorily disk according to normative EN 847-1
- Use obligatorily the regulatory push stick and save it away
if not use it.
- Use of fast steel disks prohibited (HSS)
- Use of defective or deformed prohibited
- Replace the table insert when worn
Removing the cutting blade
1 Lock the head in the up position by turning the head
upwards until it stops.
2 Remove the casing lock screw (13).
3 Pull up on the guard to remove it.
4 Keep the cutting blade still by pressing the locking lever
(11) found on the motor and loosen the blade screw by
turning it clockwise.
5 Remove the blade to be replaced
Changing the cutting blade
1 Carefully clean all sawdust and dirt from the brackets,
flanges and inside of the guards.
2 Place the new cutting blade so that the direction of
the arrow on the front of the casing matches the arrow
)
X
X
X
ENGLISH
16
engraved on the blade and the tilt of the blade's teeth.
3 Attach the flange and its screw
4 Turn the screw counter-clockwise while the blade is
locked by means of the blade locking lever (11)
5 Return the guard to its original protective position by
pulling it downward. Once the guard is set, put the locking
screw back in its place (13). Once in place, make sure
that the protective casing only opens when the head is
lowered.
6
Check the correct operation by simulating a cutting
operation at idle speed.
FIXING FOR OPERATION
8.
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the support. ALL
MACHINES ARE PREPARED FOR MOUNTING CLAMPS
ALLOWING FASTENING THE PROFILE IN A SAFE
MANNER.
To avoid deformations of the workpieces during fixing thereof,
the use of wooden profiles being easily applicable to the
movable jaws of the clamps is advised.
Clamps can be easily extracted and leave the working surface
totally clear.
For cutting long workpieces under safe conditions it is
essential to hold them with additional supports.
LIMITS REGARDING THE WORKPIECE SIZE
9.
Limits for all models as included in the present manual on
page 3
GENERAL INSTRUCTIONS FOR USE
10.
Warning!
1 Do NOT use the machine if it is in a bad condition or
lacks parts including the prescribed upper guards (the
illustrations of the present manual may be used as an
orientative guide). Unplug it, remove it from the working
area and immediately send it to an authorized technical
service.
2 Know and comply with all safety measures before you
start the machine.
- Obligatory used of aspiration particle system when cutting
the wood.
Starting and stopping the machine
Information
1 The tool has 2 different mechanisms for engaging and
disengaging depending on the intended use.When used
as a mitre saw, it has only an engage/disengage switch;
when used as a cutting table, the on/off mechanism
consists of 2 buttons that engage the machine's motor
directly. Both start-up and shut-off systems are mutually
exclusive and, for safety reasons, cannot be used
interchangeably or simultaneously.
2 The equipment is provided with a safety module protecting
it against unexpected starts. If, whilst the machine is
running, the supply of electrical power should cease, the
machine will not start after reestablishment thereof. To
release the protection push the starting button 2 twice.
Warnings!
1
Never leave running machine unattended.
2
Never start the machine with locked disk and, before
starting a cut, always wait until the cutting disk has
reached its maximum speed.
3
Before stopping the machine the disk must be clear and
be rotating freely.
Start-up and shut-off when using mitre saw/lower cutting
table
Start-up: Press and hold the rectangular switch (15) on the
grip to engage the motor.
16