Descargar Imprimir esta página
GreenWorks Pro PW60L00 Manual De Instrucciones
Ocultar thumbs Ver también para PW60L00:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

A
Set-up
1
Add water to the bucket.
2
Install the bucket onto the base.
3
Lift and push down the bucket buckle to fix
the bucket.
4
Assemble pressure washer gun to spray
wand.
5
Connect desired pressure tip.
6
Push and turn clockwise one end of the high
pressure hose into the inlet coupler.
7
Thread the priming valve onto the
pressure washer outlet and rotate
clockwise until tightened. Once
installed, take the end of the included
high pressure hose and tighten onto
the valve.
8
Avant d'installer le tuyau haute pression fourni, placez la soupape sur la sortie du nettoyeur haute
Install the battery pack.
9
Turn on Pressure Washer.
WARNING:
This Quick Start Guide is not a substitute for reading the operator's manual. To reduce the risk
of injury or death, user must read and understand operator's manual before using this product.
PRESSURE WASHER
PW60L00
USING DETERGENT
■ Put the detergent into the detergent tank.
■ Install the detergent tank onto the gun.
Turn counter-clockwise the gun to tighten.
Squeeze trigger and wait approx.1 minute for soap.
SPRAY TIP
SPRAY TIP APPLICATION
Yellow - Narrow fan tip (15° )
■ The yellow pressure washer tip provides high versatility with its 15 degree angle
tip. Referred to as the washing tip, because it provides adequate pressure to
remove dirt from surfaces, but is designed to not damage many surfaces. This
15
O
pressure washer tip is designed for "sweeping" foliage or debris given its wide
angle. This tip is versatile due to its wide area of cleaning and strong pressure
application.
White - Wide fan tip (40° )
■ The white 40 degree tip, referred to as the "fan" tip creates the widest area of
cleaning with relatively low pressure. This pressure washer tip is best used for
40
O
light or delicate cleaning applications. It is recommended for light cleaning on
wood decks and other soft or delicate surfaces.
NOTE:
AUTO ON/OFF SWITCH: This Pressure washer is equipped with an
Auto Start/Stop feature.
To operate: Set the power switch to the On (I) position. Pump will
pressurize and shut down immediately.
Once the trigger of the gun is depressed the unit will turn on. Unit
will shut off and be in standby mode when trigger is released.
Missing parts, accessories or need a service center?
Do Not Return to Store
Call : 1-855-345-3934
www.GreenWorksTools.com
B
Set-up
1
Thread adapter to the male end of the
garden hose.
2
Pull back the adaptor collar and attach to the
male connector on the machine.
3
Assemble pressure washer gun to spray
wand.
4
Connect desired pressure tip.
5
Push and turn clockwise one end of the high
pressure hose into the inlet coupler.
6
Place the valve onto the pressure washer
outlet and rotate clockwise until tightened.
Once installed, take the end of the
included high pressure hose and tighten
onto the valve.
7
1. Avant d'installer le tuyau haute pression fourni, placez la soupape sur la sortie du nettoyeu
Turn on water at outlet.
8
Run water hose for 30 seconds with the
motor in OFF position. This helps drain air
120S
from the tank and lines.
30 S
9
Install the battery pack.
18
10
Turn on Pressure Washer.
IMPORTANT: Ensure water outlet is On
before turning power On to avoid damage
to the pump.

Publicidad

loading

Resumen de contenidos para GreenWorks Pro PW60L00

  • Página 1 Pull back the adaptor collar and attach to the male connector on the machine. PRESSURE WASHER Install the bucket onto the base. PW60L00 USING DETERGENT Assemble pressure washer gun to spray wand. ■ Put the detergent into the detergent tank.
  • Página 2 Tire hacia atrás del collar del adaptador y acople el conector macho a la máquina. Instale el cubo en la base. LIMPIADOR A PRESIÓN PW60L00 Una la pistola de la hidrolavadora a presión USO DE DETERGENTE a la lanza de pulverización.