HIKOKI WH 18DC Instrucciones De Manejo página 12

English
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Mounting the bit
Reversing the rotational direction
Switch operation
Removing and mounting the hook
Remaining battery indicator
How to use the LED light*
Tightening mode selector
function*
2
Charging a USB device from a
electrical outlet
Charging a USB device and
battery from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*1 How to use the LED light
NOTE
○ Press the light section switch on the switch panel to
change the lighting mode of the LED light from "Always-
ON" → "SW interlocked" → "OFF".
Figure Page
2
3
4
5
6
7
8
9
1
10
11-a
11-b
12
13
―
○ To conserve battery power, make sure to extinguish the
light as much as possible.
○ To prevent the battery power consumption caused
by forgetting to turn off the LED light, the light goes off
automatically in about 2 minutes.
*2 Tightening mode selector function
CAUTION
Select tightening mode while the trigger switch is
released. Failure to do so could result in malfunction.
By using the Tightening mode selector switch, the tightening
torque can be adjusted according to the type of work.
The Tightening mode switches between 5 diff erent modes
each time the Tightening mode selector switch is pressed.
Upon pulling the trigger switch in bolt single mode, the driver
will automatically stop after applying a number of impacts.
Soft / power / bolt and self drilling screw mode will commence
impact upon pulling the trigger switch and will continuously
apply impact without auto-stopping.
Soft mode is a mode that does not infl ict damage on thin
nails or decorative materials.
Power mode can be used for normal work up to heavy load
work.
Bolt mode has a short pull margin for the trigger switch,
making the driver ideal for high-speed tightening work.
Bolt single mode controls the impact, allowing control of the
tightening force. Use this mode for delicate work such as
tightening bolts for racks, fences, furniture, etc.
Self drilling screw mode is ideal for tightening self drilling
screws by reducing the chances of overtightening that could
result in severing the screw head, breaking the screw, or
slippage.
NOTE
○ The appropriate mode diff ers depending on the screw
and the material being screwed. Drive in a few test
screws and adjust the mode setting accordingly.
○ The tightening mode selector switch can only be set after
the battery has been installed in the driver and the trigger
switch has been pulled once.
2
LED LIGHT WARNING SIGNAL
2
(Fig. 15)
2
2
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
3
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
3
Table 3. When any of the safeguard functions are triggered,
3
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
3
4
4
4
4
5
238
12
Fig. 15