Replacing The Filter; Customer Service - DrBrowns natural flow AC178-INTL Instrucciones De Uso

DESCALING
CAUTION: Unplug from outlet and allow to cool for 60 minutes before descaling.
Mineral deposits, like limescale, may form on the metal heating element in the base. As
the mineral deposits build, it can slow or disrupt the sterilization cycle. Depending on the
water type in your area, mineral deposits may vary in appearance but the harder the water,
the quicker it builds up. Mineral deposits are not known to be harmful, but they may impair
the function of appliances or damage components. Using non-mineral bottled water can
help prevent buildup, but regular descaling is needed for best performance. To remove the
mineral deposits, follow the steps below.
1
• Remove the lower rack, tray and lid from the base.
• 2 Descale utilizing a mixture of vinegar/water:
A • Fill measuring cup to the dashed line (80 mL) with white vinegar.
B • Add an additional 30 mL of non-mineral bottled water to reach the solid FILL LINE
of the measuring cup (110 mL total).
• Pour the mixture ONTO THE HEATING PLATE
C
D • Reassemble empty unit.
E • Plug into wall outlet, press the Power Button and run a Sterilize Only cycle.
F • Empty any remaining solution and rinse with clean water.
Note: Do not use bleach, harsh abrasives or solvents to clean the heating plate,
as they may cause permanent damage and may void the warranty.
Clean Heating Plate
6
.
Mineral Deposits

REPLACING THE FILTER

CAUTION: Unplug from outlet and allow to cool for 60 minutes before
replacing filter.
Replace the filter every six months of regular use for optimal performance.
Follow the steps below:
1. The filter is located at the bottom of the base. Gently squeeze the latches on the filter
1
cover to remove it.
2
2. Remove and replace the filter, ensuring the pull tab is still visible on top of the filter.
3
3. Snap the filter cover back into position.
Note: Filter must always be used to ensure proper performance.
4 3
B
D
C
B
A
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
NO PLACE:
ONE PLACE:
TWO PLACE:
THREE PLACE:
ANGLE:
ANGLE:
A
To purchase replacement filters, contact your local distributor.
4 3
WARRANTY
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase. Any defective part will be repaired or replaced at no
charge if it has not been tampered with and appliance has been used according to these
printed instructions. This warranty gives you specific legal rights as well as other rights
which vary from state to state.
This warranty does not cover a defect that has been caused by negligence, accidents or
improper use of the appliance. To keep your Dr. Brown's™ Bottle Sterilizer and Dryer in
good condition and retain your warranty, USE ONLY AS DIRECTED.

CUSTOMER SERVICE

If you experience unsatisfactory operation or have questions/comments, please contact
your local Dr. Brown's distributor. See drbrownsbaby.com/distributors to find your local
contact.
2
2 1
D
C
B
TITLE:
THIS DRAWING AND RELATED 3D CAD DATA
HANDI-CRAFT COMPANY
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
X 2.5
HANDI-CRAFT CO. AND ARE NOT TO BE
.X 0.5
COPIED OR USED WITHOUT THE PERMISSION 4433 FLYER AVE. ST. LOUIS MO. 63116, USA
.XX 0.25
OF HANDI-CRAFT CO.
.XXX 0.13
X 0.5
MATERIAL
INTERPET PER ASME Y14.5-1994 DRAWN RBW 15JUL19
.X 0.25
OTHER HANDI-CRAFT ENGINEERING
2 f ilters are included.
STANDARDS MAY APPLY ENG APPR.
THIRD ANGLE
PROJECTION SOLIDWORKS 3D MFG/Q.A APPR. DO NOT SCALE DRAWING
2
A
DESIGN UNITS: MILLIMETERS DRAWN RBW 15JUL19 HANDI-CRAFT COMPANY
TOLERANCES UNLESS NOTED:
ENG APPR.
NO PLACE: X 2.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
ONE PLACE: .X 0.5 MFG/Q.A APPR.
TWO PLACE: .XX 0.25 TITLE:
THREE PLACE: .XXX 0.13 THIS DRAWING AND RELATED 3D CAD DATA
CONTAINS PROPRIETARY INFORMATION FILTER REPLACEMENT
ANGLE: X 0.5
ANGLE: .X 0.25 THAT ARE THE PROPERTY OF
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
DO NOT SCALE DRAWING PERMISSION OF HANDI-CRAFT CO.
SIZE C DWG. NO. REV. 1
INTERPET PER ASME Y14.5-1994
THIRD ANGLE OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
PROJECTION
MATERIAL
SOLIDWORKS 3D SCALE: 1:1 SHEET 1 OF 1
2 1
1
B
A
FILTER AND COVER
SIZE DWG. NO. REV.
A 1
SCALE: 1:2 SHEET 1 OF 1
1
7