ENGLISH
(Original instructions)
1
Pointer
2
Stopper
3
Adjusting screw
4
Lock lever
5
Angle guide
6
Knob
7
Scale
8
Down
9
Up
10 Center of blade thickness
11 Fence
SPECIFICATIONS
Model
Blade size
Cutter blade
(Outer dia. x Width x Arbor dia.) ........ 100 x 4 x 22 mm
Circular saw blade
(Outer dia. x Arbor dia.) ........................... 110 x 20 mm
Max. cutting depth
Cutter blade ....................................................... 20 mm
Circular saw blade ............................................. 25 mm
–1
No load speed (min
) .......................................... 11,000
Overall length ..................................................... 307 mm
Net weight .............................................................. 3.0 kg
Safety class ..............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting crescent shaped slots for
the placement of flat wooden dowels or biscuit by a
plunging action.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
PLATE JOINER SAFETY WARNINGS
1.
Blades must be rated for at least the speed rec-
ommended on the tool. Blades running over rated
speed can fly apart and cause injury.
2.
Always use the guard. The guard protects the
operator from broken blade fragments and uninten-
tional contact with the blade.
All manuals and user guides at all-guides.com
Explanation of general view
12 Angle scale
13 Base
14 Set plate
15 Thickness of set plate
16 Slide switch
17 Lock nut
18 Cutter blade
19 Inner flange
20 Clamp screw
21 Blade cover
22 Dust bag
3901
/II
GEA010-1
GEB020-2
23 Fastener
24 Dust nozzle
25 For Frame Joint
26 For Edge-To-Edge Joint
27 For Corner Joint
28 For T-Butt Joint
29 Circular saw blade
30 Rubber facing
31 Limit mark
32 Brush holder cap
33 Screwdriver
3.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and could give the operator an
electric shock.
4.
Use only the blades specified for this tool.
5.
Never operate the tool with the blade locked in
exposed position or without the blade cover
secured properly in place.
6.
Make sure that the blade slides smoothly before
operation.
7.
Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blades immediately.
8.
Make sure that the flange fits in the arbor hole
when installing the blade.
9.
Inspect for and remove all nails or foreign matter
from the workpieces before operation.
10. Always place the workpieces on a stable work-
bench.
11. Secure the workpieces firmly with clamp or vise.
12. NEVER wear gloves during operation.
13. Hold the tool firmly with both hands.
14. Keep your hands and body away from the cutting
area.
15. Run the tool for a while without the blade point-
ing toward anybody. Watch for vibration or wob-
bling that could indicate poor installation or a
poorly balanced blade.
16. Never reach your hands underneath the work-
pieces while the blade is rotating.
17. Do not leave the tool running unattended.
18. Always be sure that the tool is switched off and
unplugged before making any adjustments or
replacing the blade.
19. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
20. Do not use blunt or damaged blades.
21. Do not use the tool with damaged guards.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
7