Black and Decker KG115 Instrucciones Originales página 9

on the work surface without moving, or moving the tool in
a circular motion causes burning and swirling marks on
the work surface.
Remove the tool from work surface before turning tool off.
u
Allow the tool to stop rotating before laying it down.
Precautions to take when sanding paint
Sanding of lead based paint is NOT RECOMMENDED
u
due to the difficulty of controlling the contaminated dust.
The greatest danger of lead poisoning is to children and
pregnant women.
Since it is difficult to identify whether or not a paint con-
u
tains lead without a chemical analysis, we recommend the
following precautions when sanding any paint:
Personal safety
No children or pregnant women should enter the work
u
area where the paint sanding is being done until all clean
up is completed.
A dust mask or respirator should be worn by all persons
u
entering the work area. The filter should be replaced daily
or whenever the wearer has difficulty breathing.
Note: Only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting masks
do not offer this protection. See your local hardware dealer for
the proper respiratory protection.
NO EATING, DRINKING or SMOKING should be done
u
in the work area to prevent ingesting contaminated paint
particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or
smoking should not be left in the work area where dust
would settle on them.
Environmental safety
Paint should be removed in such a manner as to minimize
u
the amount of dust generated.
Areas where paint removal is occurring should be sealed
u
with plastic sheeting of 4 mils thickness.
Sanding should be done in a manner to reduce tracking of
u
paint dust outside the work area.
Cleaning and disposal
All surfaces in the work area should be vacuumed and
u
thoroughly cleaned daily for the duration of the sanding
project. Vacuum filter bags should be changed frequently.
Plastic drop cloths should be gatheredup and disposed
u
of along with any dust chips or other removal debris.
They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures.
During clean up, children and pregnant women should be
kept away from the immediate work area.
All manuals and user guides at all-guides.com
u
Using cutting wheels
Do not use edge grinding/cutting wheels for surface grinding
applications because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and injury may result.
u
u
u
u
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u
u
u
u
u
u
u
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u
u
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
(Original instructions)
All toys, washable furniture and utensils used by children
should be washed thoroughly before being used again.
Allow tool to reach full speed before touching tool to work
surface.
Apply minimum pressure to work surface, allowing tool to
operate at high speed. Cutting rate is greatest when the
tool operates at high speed.
Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage.
Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before setting it down.
Switch off and unplug the appliance/tool.
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
ENGLISH
9