General Safety Rules - SCOPREGA PCS Manual De Instrucciones

M A N U A L O F
SAVE THIS INSTRUCTIONS MANUAL FOR REFERENCE
2. FOREWORD
Dear customer,
congratulations on choosing Scoprega.
We design and manufacture products of the highest quality to meet the needs
of our customers. Scoprega offers the highest quality in service as well. Our
specialised departments provide support and instructions when needed, as well
as comprehensive technical service.
We thank you for your trust.
WARNING
Read these instructions before using the inflator. Failure to follow all the instructions listed
below may result in damage to the product and/or cause serious injury to persons.
3. PRELIMINARY WARNINGS
1. Comply with all instructions in this document.
2. Keep these instructions.
3. Always protect the power cable.
4. Do not open the inflator. Refer all servicing to qualified service personnel authorised by Scoprega.
Servicing is required when the device is damaged or not working in any way.
5. Do not tamper with the product. Opening the inflator will void its warranty.
6. Provide suitable ventilation.
7. Avoid placing objects near the product during operation.
8. Keep this product out of the reach of children.
9. The operating inflator produces vibrations: therefore, we recommend you to use it on the floor, so as
to avoid accidental falls.
DO NOT POWER THE INFLATOR WITH A
VOLTAGE HIGHER THAN THE RATED ONE

4. GENERAL SAFETY RULES

1. ALWAYS TAKE INTO ACCOUNT THE WORKING ENVIRONMENT.
Do not expose the inflator to rain. Do not use in the presence of flammable liquids or gases.
2. AVOID UNINTENTIONAL STARTING.
Do not start the inflator with the inlet in contact with dust or water.
3. PAY ATTENTION.
Pay attention to what you are doing. Use common sense.
4. CHECK THAT THERE ARE NO DAMAGED PARTS.
Before using the inflator, carefully check its outer sides and components.
5. DO NOT OPERATE
portable inflators near flammable liquids or in gaseous or explosive
atmospheres. The inflator motors produce sparks that can release fumes.
6. DO NOT INHALE!
The compressed air coming from the inflator is not clean. Never inhale air from your inflator.
10
I N S T R U C T I O N S
7. WARNING! RISK OF EXPLOSION.
Inflate the inflatable unit only complying with the manufacturer's recommendations. Exceeding the
pressure rating could cause the inflator to explode, resulting in personal injury.
8. NEVER LEAVE THE DEVICE UNATTENDED.
Overinflation could result in serious injury and property damage.
9. WARNING! RISK OF UNSAFE OPERATION.
Do not modify or attempt to repair the unit. Do not drill into or make any modifications to the inflator
or its accessories. Any modification to the product will void its warranty.
10. Never carry the inflator by the flexible hose or power cable.
5. INTRODUCTION
The PCS system is a device capable of maintaining the rated pressure inside great inflatable items
within preset values (min.90 mbar, max. 450 mbar), regardless of ambient temperature. The unit
constantly monitors pressure variation inside the inflatable item and regulates its operation to ensure
refilling and release of pressure. In the event of a temporary power failure, the PCS system maintains all
preset values and will restart as soon as power is restored.
6. INFLATOR DESCRIPTION
The PCS (pressure control system) is a unit capable of inflating, maintaining a preset pressure value
and deflating a large inflatable item. This means that the unit must always be connected to the
inflatable item.
The unit protection degree is IP65 and can be operated in rainy or dusty conditions.
The PCS is supplied with adapters to be connected to the most common inflation valves
The inflator is equipped with a thermal overload switch that trips in case of overheating. Normal
operation will restart automatically after a 20/40-minute pause
PCS-IC MODEL (code: K6130651)
The PCS-IC model differs from the standard model as pressure is detected
by a sensor inside the inflator itself. Therefore, it does not feature the pressure sensor
and the cable to be connected to the inflatable unit. This model is only intended for use with
40mm diameter hoses with suitable valves (we suggest our BRAVO 260 H.V, code:
A131000N)
7. TECHNICAL SPECIFICATIONS
1. Power supply
2. MAX. power
3. Pressure range
4. MAX. flow rate
5. Dimensions
6. Weight
7. Protection degree
8. Pressure check cable length*
9. Rated pressure
*not provided on PCS-IC model
210-240 V AC, 50 Hz or 110-130 V AC, 60 Hz
2500 W
90-450 mbar (1.3-6.5 psi)
2800 l/min
700x250x h 350 mm
15 kg
IP65 - IEC 60529
10 metres
on request (within range)
11