Important Charging Notes; Installing And Removing The Battery Pack; Assembly And Adjustments - Black and Decker BHFEA18 Manual De Instrucciones

Ocultar thumbs Ver también para BHFEA18:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Important Charging Notes

1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR FUTURE

ASSEMBLY AND ADJUSTMENTS


WARNING:
serious personal injury, turn unit off and remove
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Assembly (Fig. C)
1. Align the top of the extension tube 
inlet 
 15 
as shown in Fig. C.
2. Push the extension tube 
it locks into position.
3. To remove an accessory, press the extension pole release
button 
 7 
located on the vacuum inlet or the bottom
of the extension tube and gently pull the connected
accessory off.

WARNING:
unit with the rear of the vacuum facing a wall so that
any inadvertent fall of the unit would contact a wall
and not people or pets.
Shock hazard. Disconnect the
USE
To reduce the risk of
 8 
with the vacuum
 8 
onto the vacuum inlet 
When not in use position the
OPERATION

WARNING:
serious personal injury, turn unit off and remove
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. F)
NoTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack 
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 
 13 
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Use (Fig. A, G)
This vacuum cleaner can be used in one of two ways.
With the extension tube 
With the crevice tool 
Switching ON and OFF (Fig. H)
To switch ON, push the ON/OFF button 
For increased power, push the ON/OFF button 
NoTE: The state of charge indicator LEDs will illuminate
while the vacuum is ON.
To switch OFF, press the ON/OFF button 
Floor Sense
Floor Sense is active in the low speed. When a carpet is
detected, the performance of the unit is automatically
increased to high speed. When a hard floor is detected, the
performance of the unit reduces to low speed.
 15 
so
Using an Accessory Tool (Fig. G)
The crevice tool 
hard to‑reach places.
To attach the crevice tool 
so it locks into position as shown in Fig. G.
To release the crevice tool 
release button 
To reduce the risk of
 12 
into the tool handle, align the
 8 
and the floor head 
 11 
.
 11 
allows for vacuuming in narrow and
 11 
press into vacuum inlet 
 11 
press the crevice tool
 16 
and gently pull the extension tube off.
ENglIsh
 9 
.
 1 
.
 1 
 again.
 1 
a third time.
 15 
25

Publicidad

Tabla de contenido
loading

Tabla de contenido