Intended Use; Technical Data; Before Starting The Equipment - EINHELL TE-CD 18/48 Li-i Manual De Instrucciones

18V 5.2Ah PXC Plus Lithium-Ion battery
18V 4.0Ah/6.0Ah PXC Plus Lithium-Ion battery
18V 5.0Ah/8.0Ah PXC Plus Lithium-Ion battery
18V PXC Dual Port Fast Charger
18V PXC Fast Charger
Contact your local retailer for more specifi c
models of batteries and charger available in your
area. You can also explore battery + charger
options at Einhell.com.

3. Intended use

The cordless hammer drill driver is designed
for tightening and undoing screws, as well as
for drilling in wood, metal, plaster, concrete and
plastic.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: .............................18 V
Idling speed: ............... 0-400/0-1500 RPM (min
Torque settings: ....................................... 21+1+1
Clockwise/counter-clockwise: ........................yes
Clamping range of drill chuck: .. max. ½'' (13 mm)
Hammer Speed: ................. 0-6400/0-24000 bpm
Torque: ................................... 390 in-lbs (44 Nm)
Weight (Tool only): ........................... 4 lbs (1.8 kg)
Max. screw diameter: ........................... ¼'' (6 mm)
The maximum screw diameter indicates the
maximum diameter of the screw that can be
screwed into wood. The screw diameter can vary
depending on the type of wood.
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Anl_TE_CD_18_48_Li_i_SPK7_USA.indb 11 Anl_TE_CD_18_48_Li_i_SPK7_USA.indb 11
EN
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's con-struction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

)
-1
Be sure to read the following information before
you put the cordless hammer drill driver into
operation:
1. Charge the battery pack with the charger
(battery and charger not included). An empty
battery pack requires a charging period of
approximately 0.5 to 1 hour.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwdriving in walls.
- 11 -
03.05.2022 12:57:09 03.05.2022 12:57:09