Cleaning And Storage; Troubleshooting Chart; Specifications - Cub Cadet BC509 Manual Del Operador

MAINTENANCE AND REPAIR INSTRUCTIONS
REPLACING THE SPARK PLUG
Use a replacement part number 753-05784 or
Champion ® #RDZ4H spark plug. The correct air
gap is 0.025 in. (0.635 mm).
1. Stop the engine and allow it to cool. Remove the
six (6) screws on the back of the engine cover
with a Flat-head or T-25 Torx screwdriver (Fig.
44).
2. Grasp the plug wire firmly and pull the cap from
the spark plug.
3. Clean dirt from around the spark plug. Remove
the spark plug from the cylinder head by turning
a 5/8 in. socket counterclockwise.
WARNING: Do not sand blast,
scrape or clean electrodes. Grit in the
engine could damage the cylinder.
4. Replace cracked, fouled or dirty spark plug. Set the air gap at 0.025 in.
(0.635 mm.) using a feeler gauge (Fig. 45).
5. Install a correctly-gapped spark plug in the cylinder head. Turn the 5/8
in. socket clockwise until snug.
If using a torque wrench torque to: 110-120 in.•lb. (12.3-13.5 N•m) Do
not over tighten.

CLEANING AND STORAGE

CLEANING
WARNING:
To avoid serious personal injury, always turn the unit off and allow it to cool
before cleaning or servicing it.
Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners
that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic
housing or handle. Wipe off any moisture with a soft cloth.
STORAGE
• Never store the unit with fuel in the tank where fumes may reach an open flame or spark.
• Allow the engine to cool before storing.
• Lock up the unit to prevent unauthorized use or damage.
• Store the unit in a dry, well-ventilated area.
• Store the unit out of the reach of children.
Short Term Storage (1-2 weeks)
1. Store the unit in a horizontal position. If this is not possible, store the unit vertically with the engine at
the top.
Long Term Storage
1. Drain all gasoline from the gas tank into a container. Do not use gas that has been stored for more
than 30 days. Dispose of the old gasoline in accordance with federal, state and local regulations.
2. Start the engine and allow it to run until it stalls. This ensures that all gasoline has been drained from
the carburetor.
3. Allow the engine to cool. Remove the spark plug and put 5 drops of high quality motor oil into the
cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the
trimmer after storage.
4. Change the oil, referring to Changing the Oil. Dispose of the old oil in accordance with federal, state
and local regulations.
5. Thoroughly clean the unit and inspect for any loose or damaged parts. Repair or replace damaged
parts and tighten loose screws, nuts or bolts. The unit is ready for storage.
View Of The Rear Engine Cover
Screws
Fig. 44
0.025 in.
(0.635 mm.)
Fig. 45
CAUSE
ENGINE WILL NOT START
Empty fuel tank
Primer bulb wasn't pressed enough
Old fuel (over 30 days)
Screws Fouled spark plug
Engine is over heated
ENGINE WILL NOT IDLE
Air filter is plugged
Old fuel (over 30 days)
Improper idle speed
ENGINE WILL NOT ACCELERATE
Old fuel (over 30 days)
Cutting attachment bound with grass
Dirty air filter
ENGINE LACKS POWER OR STALLS WHEN CUTTING
Old fuel (over 30 days)
Fouled spark plug
The outside temperature is above 90˚ F
CUTTING ATTACHMENT WILL NOT ADVANCE LINE
Cutting attachment bound with grass
Cutting attachment out of line
Inner reel bound up
Cutting head dirty
Line welded
Line twisted when refilled
Not enough line is exposed
CUTTING LINE ADVANCES UNCONTROLLABLY
Oil, cleaner or lubricant in cutting head
IF FURTHER ASSISTANCE IS REQUIRED, CONTACT YOUR AUTHORIZED SERVICE DEALER.
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 4-Cycle
Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 cu. in. (29 cc)
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 inch (0.655 mm)
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAE 30 Oil
Crankcase Oil Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.04 oz (90 ml)
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 oz (414 ml)
Approximate Unit Weight (No fuel, with handle, cutting attachment and shield) . . 12-13.5 lbs (5.4-6 kg)
Trimming Line Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.105 inches (2.67 mm)
Cutting Path Diameter, Trimmer Head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 inches (45.7 cm)
Cutting Path Diameter, Blade Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 inches (204 mm)
Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Quick-Snap
*All specifications are based on the latest product information available at the time of printing. We
reserve the right to make changes at any time without notice.
TROUBLESHOOTING
ACTION
Fill fuel tank with fuel
Press primer bulb fully and slowly 10 times
Drain fuel tank and add fresh fuel
Replace or clean the spark plug
Move the choke lever to Position 2, squeeze the throttle
control and pull the starter rope until the unit starts. Run
the unit for 2-5 minutes. Then move the choke lever to
Position 3.
Replace or clean the air filter
Drain fuel tank and add fresh fuel
Adjust according to the Idle Speed Adjustment section
Drain gas tank and add fresh fuel
Stop the engine and clean the cutting attachment
Clean or replace the air filter
Drain fuel tank and add fresh fuel
Replace or clean the spark plug
Move the choke lever to Position 2, press the primer
bulb 10 times, squeeze the throttle control and pull the
starter rope until the unit starts. Run the unit for 2-5
minutes. The unit may be used during this time. Then
move the choke lever to Position 3.
Stop the engine and clean cutting attachment
Refill with new line
Replace the inner reel
Clean inner reel and outer spool
Disassemble, remove the welded section and rewind
Disassemble and rewind the line
Push the bump head and pull out line until 4 inches
(102 mm) of line is outside of the cutting attachment
Clean and thoroughly dry the cutting head

SPECIFICATIONS

7