Installing And Removing The Battery Pack - DeWalt DCS692 Manual De Instrucciones

the D WALT Tool Connect™ app. For proper installation of
e
the D WALT Tool Tag, refer to the D
e
To learn more, visit:
www.D WALT.com/en‑us/jobsite‑solutions/tool‑connect
e
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

Installing and Removing the Battery Pack

(Fig. G)
nOTE: For best results, make sure your battery pack is
fully charged. Use only D
e
this cut‑off machine.
Unlock battery door by moving battery door latch
5
towards the front of the tool and open as shown in Figure G.
To install the battery pack
battery pack with the rails inside the tool and slide it in
until the battery pack is firmly seated. Ensure that it does
not disengage.
Close the battery door 5
toward the back of the tool to lock the battery door.
To remove the battery pack from the tool, unlatch and open
the battery door. Then press the battery release button
and firmly pull the battery pack out of the tool. Insert it into
the charger as described in Charging a Battery.
Do not leave the battery door open.
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.

WARNING: Never use the cut‑off machine with one hand.
Always grip the cut‑off machine firmly with both hands.

WARNING: Make sure the handles and grips of
your cut‑off machine are secure and free of grease
and/or moisture.
Proper hand position for both left‑ and right‑handed users
requires your right hand on the rear handle
hand on the front handle
Wireless Tool Control (Fig. A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the tool.
Your tool is equipped with a Wireless Tool Control
transmitter which allows your tool to be wirelessly paired
with another Wireless Tool Control device, such as a D
dust extractor.
To pair your tool using Wireless Tool Control, depress the
trigger switch and the Wireless Tool Control pairing
2
button on the seperate device. An LED on the seperate
WALT Tool Tag manual.
e
WALT FLEXVOLT™ batteries with
19 into the tool, align the
, and push the battery door latch
and your left
1
.
8
device will let you know when your tool has been
successfully paired.
Heavy Load Indicator LED (Fig. A)
The heavy load indicator LED
when the tool is being pushed too hard. Continuing to use
the tool after the LED is lit could cause the tool to shut down
or reduce run time.
Reducing the Risk of Kickback (Fig. I)

WARNING: Reactive forces may occur at any time
the cutting wheel is in motion.

WARNING: To reduce the risk of kickback, avoid
cutting with the upper quadrant of the cutting
wheel whenever possible. Be extremely mindful of
binding or pinching of the cutting wheel in this area as
it can cause severe reactive forces resulting in kickback.
• Always be alert to any potential movement that could
4
cause the material being cut to close and pinch the
cutting wheel.
• Proper support of the material will ensure the cut stays
open during the cut. If you cannot properly support the
material, do not use a cut‑off machine to make your cut.
• Always support exposed pipe in the ground so that it
4
is stable and is able to support weight. Use additional
support closer to the area to be cut to prevent the pipe
from sagging and pinching the cutting wheel.
20
• Material that is under stress could shift when it is cut.
Uneven pipe beds could exert stress.
• Always make sure the section of material being removed
is also supported. After the first cut is made you may
have to move supports or add additional support to
ensure both sides of the material are evenly supported.
• Be aware of weakened work areas that could shift or slide
causing your supports to move.
Making Cuts with a Cut‑Off Machine

CAUTION: Before attempting to start, grasp tool firmly
with both hands before lifting.

WARNING: Cut‑off saw not intended for surface
grinding or other applications where side loading of
the blade is encountered.

WARNING: Edge cutting can be performed only with
wheels that are designed and specified for this purpose.
Protect yourself during edge cutting by directing the
open side of the guard away from you, the operator.

WARNING: Wheels used for cutting may break or kick
back if they bend or twist while the tool is being used to
do cut‑off work.

WARNING: Always be alert for gyroscopic forces that
can be generated by a rapidly spinning cutting wheel.
Moving the cut‑off machine sideways can create a
WALT
e
gyroscopic force, causing the operator to experience an
unexpected perpendicular change in direction.
Wet Cut Method (Fig. A, J, K)

CAUTION: Close battery door and securely latch it
closed before using any water.
English
7 will illuminate as a warning
13