Scheppach HS105 Traducción Del Manual De Instrucciones Original página 33

c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing pow-
er tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety instructions for table saws
Guarding related warnings
a) Keep guards in place. Guards must be in work-
ing order and be properly mounted.
A guard that is loose, damaged, or is not function-
ing correctly must be repaired or replaced.
b) Always use saw blade guard and riving knife
for every through-cutting operation.
For separating cuts where the saw blade cuts com-
pletely through the thickness of the workpiece, the
protective cover and other safety devices help re-
duce the risk of injury.
c) Immediately reattach the guarding system after
completing an operation (such as rabbeting, da-
doing or resawing cuts) which requires removal
of the saw blade guard and/or riving knife.
The guard and riving knife help to reduce the risk
of injury.
d) Make sure the saw blade is not contacting the
guard, riving knife or the workpiece before the
switch is turned on.
Inadvertent contact of these items with the saw
blade could cause a hazardous condition.
e) Adjust the riving knife as described in this in-
struction manual. Incorrect spacing, positioning
and alignment can make the riving knife ineffective
in reducing the likelihood of kickback.
f) For the riving knife to work, they must be en-
gaged in the workpiece. The riving knife is inef-
fective when cutting workpieces that are too short
to be engaged with the riving knife. Under these
conditions a kickback cannot be prevented by the
riving knife.
g) Use the appropriate saw blade for the riving
knife. For the riving knife to function properly, the
saw blade diameter must match the appropriate
riving knife and the body of the saw blade must be
thinner than the thickness of the riving knife and
the cutting width of the saw blade must be wider
than the thickness of the riving knife.
Cutting procedures warnings
a) m DANGER: Never place your fingers or
hands in the vicinity of the saw blade or in the
sawing area.
A moment of inattention or a slip could direct your
hand towards the saw blade and result in serious
personal injury.
b) Feed the workpiece into the saw blade or cut-
ter only against the direction of rotation.
Feeding the workpiece in the same direction that
the saw blade is rotating above the table may re-
sult in the workpiece, and your hand, being pulled
into the saw blade.
c) Never use the mitre gauge to feed the work-
piece when ripping and do not use the rip
fence as a length stop when cross cutting with
the mitre gauge.
www.scheppach.com GB | 33