Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
HOW TO TRANSPORT THE APPLIANCE
To transport the machine, proceed as follows:
1. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
supply(Fig.1), and if not, disconnect it.
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
2. Check that the handlebar is in the vertical position, if not, press the uncoupling lever (4) (Fig.2)
and turn the handlebar to the vertical position (Fig.3). When the handlebar is vertical, release the
uncoupling lever (4).
4
3
1
2
1
2
3. Disconnect the power supply connector of the brush head motor (5) from the power connector (6) on
the control handlebar (Fig.4).
4. Disconnect the male quick coupling (7), on the supply pipe that goes to the spray nozzles from the
female quick coupling (8) (Fig.5), in the solenoid valve outlet pipe.
5. Set the catches (9) in the brush head body to the rest position. Move and turn the knobs by a quarter
turn (Fig.6). (ONLY FOR EXTRA VERSION)
6. Lightly tip the machine back (Fig.7), block one of the rear wheels and shift the control column
backwards. Remove the brush head body from the frame.
7
7
6
4
5
7
COMPONENT POSITIONING
The basic components of the appliance are as follows:
1. Dead man's lever (Fig.1).
2. Control lever main switch (positioned under the grip of the handlebar) (Fig.1).
3. Lever for adjusting handlebar inclination (Fig.1).
4. Control lever for detergent distribution valve (Fig.1).
5. Spray kit control switch (Fig.1).
6. Brush head motor thermal trip unit (Fig.2).
7. Spray kit power socket (Fig.2).
8. The appliance's power cable (Fig.3).
9. Spray kit power cable (Fig.3).
2
1
3
6
5
4
1
2
10. Solution tank kit upper support (Fig.4).
11. Solution tank kit lower support (Fig.4).
12. Top cable tidy (Fig.5).
13. Bottom cable tidy (Fig.5).
14. Detergent solution tank (Fig.6).
15. Detergent solution cap (Fig.6).
16. Spray kit detergent solution draught tube (Fig.6).
17. Spray kit detergent solution draught filter (Fig.6).
18. Detergent solution supply tube (Fig.7).
19. Spray kit detergent solution nozzle support (Fig.7).
10
11
4
5
18
19
7
To operate the machine, do as follows:
1. Bring the catches (1) in the brush head body, to the rest position. Move and turn the knobs by a
2. Lightly tip the machine back (Fig.2), block one of the rear wheels and shift the control column
3. Turn the brush head to the vertical position. Bring the rotated brush head into contact with the floor
1
4. Unscrew and remove the tightening keys (2) (Fig.4).
5. Remove the pad holder stop flange (3) (Fig.5).
3
6. Insert the pad holder, being careful to centre the fixing pins (4) in the appliance with the holes (5) in
7. Insert the pad holder stop flange (3) (Fig.7)
8. Screw in the tightening keys (2) (Fig.8)
9. Lightly tip the machine back (Fig.9), block one of the rear wheels and shift the control column
10. Turn the brush head into the work position (Fig.10).
8
9
6
Fill the solution tank only when the column is in vertical position, by proceeding as follows:
1. Take the device to the dedicated maintenance area.
2. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
3. Remove the solution tank cap (4) (Fig.2).
9
4. Remove the water distribution pipe (5) in the hole on the brush head (6) (Fig.3).
7
8
3
5. Disconnect the detergent solution pipe (7) from the quick coupling (8) (Fig.4).
15
6. Remove the detergent solution pipe (7) from the hole in the solution tank (Fig.5).
7. Remove the solution tank tap tie-rod chain (8) in the coupling in the tap control handle (9) (Fig.6).
12
16
13
7
17
6
8
19
PREPARING THE APPLIANCE
HOW TO ASSEMBLE THE APPLIANCE
quarter turn (Fig.1).
backwards.
(Fig.3).
1
2
the pad holder (Fig.6).
ATTENTION: To tighten the keys correctly use a tightening clamp.
backwards.
3
7
8
10
PUTTING IN THE DETERGENT SOLUTION
ATTENTION: the place designated for this operation must comply with current environmental
protection regulations.
supply(Fig.1), and if not, disconnect it.
ATTENTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
3
1
2
1
2
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
7
4
5
3
2
9
5
6
4
3
9
8
6
Publicidad
Tabla de contenido
