Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
MAINTENANCE
RECOMMENDED MAINTENANCE OPERATIONS
TYPE OF MAINTENANCE
Checking and cleaning the pad holder
Checking and cleaning the solution tank
Checking and cleaning the detergent solution draught filter system
Checking and cleaning the detergent solution spray nozzle
CHECKING AND CLEANING THE PAD HOLDER
Careful cleaning of the pad holder guarantees better cleaning of the floor as well as a longer brush motor
life. To clean the pad holder, proceed as follows:
1. Take the appliance to the dedicated dirty water drainage area.
ATTENTION: the place designated for this operation must comply with current environmental
protection regulations.
2. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
supply(Fig.1), and if not, disconnect it.
ATTENTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
3. Check that the handlebar is in the vertical position, if not, press the uncoupling lever (4) (Fig.2)
and turn the handlebar to the vertical position (Fig.3). When the handlebar is vertical, release the
uncoupling lever (4).
3
1
2
1
2
4. Lightly tip the machine back (Fig.4), block one of the rear wheels and shift the control column
backwards.
5. Turn the brush head into the vertical position (Fig.5).
6. Bring the rotated brush head into contact with the floor (Fig.6).
7. Remove the pad holder, and remove the impurities in it.
8. Repeat the operations in reverse order to reassemble all the parts.
ATTENTION: To tighten the keys correctly use a tightening clamp.
4
5
CHECKING AND CLEANING THE SOLUTION TANK
Carefully cleaning the solution tank ensures the floor is cleaned properly. Proceed as follows to clean
the solution tank:
1. Take the device to the dedicated maintenance area.
ATTENTION: the place designated for this operation must comply with current environmental
protection regulations.
2. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
supply(Fig.1), and if not, disconnect it.
ATTENTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
3. Make sure the solution tank is empty, otherwise empty it completely.
4. Remove the solution tank cap (4) (Fig.2).
5. Remove the water distribution pipe (5) in the hole on the brush head (6) (Fig.3).
3
1
2
1
2
6. Disconnect the detergent solution pipe (7) from the quick coupling (8) (Fig.4).
7. Remove the detergent solution pipe (7) from the hole in the solution tank (Fig.5).
8. Remove the solution tank tap tie-rod chain (8) in the coupling in the tap control handle (9) (Fig.6).
9. Turning the closing knob (10) (Fig.7) shift the top brackets beyond the stops in the tank.
7
8
X
X
X
X
X
X
X
X
10. Remove the solution tank kit from the appliance, to lift it use the handle on the tank.
11. Rinse the inside with a jet of water, if necessary use a spatula to remove the sludge that has
X
X
accumulated at the bottom of the tank.
12. Put the solution tank on the column, so that the bottom of the tank is anchored to the fixed bracket
(11) on the column itself (Fig.8).
13. Holding the tank with one hand, move the mobile bracket (12) down until the solution tank is locked
to the column (Fig.9).
10
14. Lock the position of the mobile bracket (12) by tightening the closing knob (10) (Fig.10).
15. Insert the water distribution pipe (5) in the hole on the brush head (6) (Fig.11).
16. Insert the solution tank tap tie chain (8) in the coupling in the tap control handle (9) (Fig.12).
4
10
3
17. Insert the detergent solution pipe (7) into the hole in the solution tank (Fig.13).
18. Connect the detergent solution draught filter (7) to the quick coupling (8) (Fig.14). Make sure that the
draught filter stays inside the solution tank.
19. Insert the solution tank cap (4) (Fig.15).
7
Proceed as follows to clean the detergent solution draught filter:
1. Take the device to the dedicated maintenance area.
2. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
supply(Fig.1), and if not, disconnect it.
3. Make sure the solution tank is empty, otherwise empty it completely.
4. Remove the solution tank cap (4) (Fig.2).
5. Disconnect the detergent solution pipe (5) from the quick coupling (6) (Fig.3).
6. Clean the filter under running water, if necessary remove any impurities.
7. Repeat the operations in reverse order to reassemble all the parts.
5
6
4
3
21
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
7
4
5
ATTENTION: Be careful not to lose the detergent solution draught filter.
11
7
8
5
6
10
11
8
7
13
14
CHECKING AND CLEANING THE DETERGENT SOLUTION DRAUGHT FILTER
ATTENTION: the place designated for this operation must comply with current environmental
protection regulations.
ATTENTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
3
1
2
1
2
9
8
6
12
9
9
8
12
4
15
5
6
4
3
Publicidad
Tabla de contenido
