Ec Declaration Of Conformity - COMAC CM43 orbital spray Manual De Uso Y Mantenimiento

CHECKING AND CLEANING THE DETERGENT SOLUTION SPRAY NOZZLE
To clean the detergent solution spray nozzle proceed as follows:
1. Take the device to the dedicated maintenance area.
ATTENTION: the place designated for this operation must comply with current environmental
protection regulations.
2. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
supply(Fig.1), and if not, disconnect it.
ATTENTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
3. Make sure the solution tank is empty, otherwise empty it completely.
4. Remove the ring nut fixing the nozzle (4) (Fig.2).
5. Remove the spray nozzle (5), being careful not to lose the washer (6) (Fig.3).
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
6. Clean the nozzle under a jet of running water, if necessary remove any impurities.
7. Repeat the operations in reverse order to reassemble all the parts.
3
1
2
1 2
DISPOSAL
To dispose of the appliance, take it to a demolition centre or an authorised
collection centre.
Before scrapping the appliance, it is necessary to remove and separate
out the following materials, then send them to the appropriate collection
centres in accordance with applicable environmental hygiene regulations:
• Pad holders or brushes
• Electric and electronic parts*
• Plastic parts
• Metallic parts
(*) In particular, contact your distributor when scrapping electric and
electronic parts.
TROUBLESHOOTING
This chapter lists the most common problems linked with the use of the appliance. If you are unable to
resolve the problems with the information given here, please contact your nearest assistance centre.
PROBLEM POSSIBLE CAUSE
The power cable extension
is not connected to the mains
socket.
The power cable extension
is not
appliance's power cable.
The electrical specifications
of the
correspond to the electrical
THE APPLIANCE DOES NOT specifications of the power
SWITCH ON supply network.
Extension cable damaged.
Overheating of the brush head
motor.
INSUFFICIENT DETERGENT The amount of detergent in the
SOLUTION ON THE PAD solution tank is insufficient for
HOLDER the work that needs doing.
5
6
4
3
SOLUTION
Check that the plug on the
extension cable has
inserted into the mains supply
socket.
Check that the plug on the
cable of the appliance has
connected to the
been inserted into the socket
on the extension cable.
Make sure that the electrical
specifications of the appliance
appliance should correspond to the electrical
specifications of the power
supply network, check the
technical information on the
serial number plate.
Check the extension cable
is not damaged, and if it is,
replace it.
Make sure that the thermal
breaker on the back of the
handlebar has not tripped. If it
has, wait a few minutes until it
has cooled down, then press
the specific circuit breaker
button to reactivate the power
supply and motor operation
Make sure that the amount
of detergent solution in the
solution tank is sufficient for the
work to be carried out, and if
necessary fill the solution tank.

EC DECLARATION OF CONFORMITY

37059 Santa Maria di Zevio (VR) Italy
declares under its sole responsibility that the products
comply with the requirements of the following Directives:
• 2006/42/EC: Machinery Directive.
• 2014/35/UE: Low Voltage Directive.
• 2014/30/UE: Electromagnetic Compatibility Directive.
• 2011/65/UE: RoHS
The person authorized to compile the technical file:
Mr. Giancarlo Ruffo
Via Maestri del Lavoro, 13
37059 Santa Maria di Zevio (VR) Italy
been
22
The undersigned manufacturer:
COMAC S.p.a.
Via Maestri del Lavoro, 13
SINGLE DISC MACHINE
mod. CM 43 ORBITAL SPRAY
COMAC S.p.a.
Legal representative
Giancarlo Ruffo