At The End Of The Work - COMAC CM43 orbital spray Manual De Uso Y Mantenimiento

8. Turning the closing knob (10) (Fig.7) shift the top brackets beyond the stops in the tank.
9. Remove the solution tank kit from the appliance, to lift it use the handle on the tank.
10. Fill with clean water, at a temperature no higher than 50°C.
11. Insert the solution tank cap (4) (Fig.8).
12. Put the solution tank on the column, so that the bottom of the tank is anchored to the fixed bracket
(11) on the column itself (Fig.9).
7
10
7 8
13. Holding the tank with one hand, move the mobile bracket (12) down until the solution tank is locked
onto the column (Fig.10).
14. Lock the position of the mobile bracket (12) by tightening the closing knob (10) (Fig.11).
15. Insert the water distribution pipe (5) into the hole on the brush head (6) (Fig.12).
10
12
10 11
16. Insert the solution tank tap tie-rood chain (8) into the coupling in the tap control handle (9) (Fig.13).
17. Remove the solution tank cap (4) (Fig.14).
18. Insert the detergent solution pipe (7) into the hole in the solution tank (Fig.15).
9
4
8
13 14
19. Connect the detergent solution draught filter (7) to the quick coupling (8) (Fig.16). Make sure that the
draught filter stays inside the solution tank.
20. Add the liquid detergent to the tank in the concentration and manner indicated on the detergent
manufacturer's label. The formation of excess foam could damage the internal components of the
machine, so only use the minimum amount of detergent needed.
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
ATTENTION: We recommend that you vacuum at intervals the dirt-loaded foam with a vacuum
cleaner for liquids.
21. Insert the solution tank cap (4) (Fig.17).
8
7
4
16 17
Before beginning to work, it is necessary to:
1. Before using, the appliance must be in order and safe to use with the work equipment, especially the
power cable and the extension cable. If everything is not in order, the appliance must not be used.
2. Insert the plug (1) of the power supply cable (2) in the mains supply socket (3) (Fig.1).
3. Release the control handlebar from the vertical position. Press the control column stop lever (4) in
the direction indicated by the arrow (Fig.2) and turn the control column towards yourself (Fig.3).
ATTENTION: During this operation, do not rest your foot on the appliance.
3
1
2
1 2
4. Turn the steering column control towards you until you find the right position that allows you to
operate the appliance comfortably.
5. Once the ideal position has been found, release the control column stop lever (4) to lock the
handlebar.
6. Turn the dead man's handle towards you (5) (Fig.4).
7. Press the control levers main switch (6), located under the grips on the handlebar (Fig.5).
8. The appliance will now start to move.
9. Apply a small amount of detergent solution to the floor by pressing the lever (7) (Fig.6), until the brush
is saturated with foam (optional solution tank kit).
11
9
5
6
12
7
15
WORK
4
3
5
6
4
10. If you intend to use the spray system, operate the lever of pump control switch (8) on the control
handlebar.
ATTENTION: Pushing the lever (8) forwards starts the pump in intermittent mode (Fig.7).
ATTENTION: Pushing the lever (8) backward starts the pump in continuous mode.
11. Push the machine with the brush rotating from left to right or vice versa.
12. Immediately afterwards, push the machine in the same way but in the opposite direction, so that
about one quarter of the working width overlaps the previous one.
13. We recommend that you vacuum up the dirt-loaded foam at intervals with the aid of a vacuum cleaner
for liquids (optional solution tank kit).
ATTENTION: The first time an operator uses the machine, he/she should become familiar with the
movements to be imparted to the shaft in order to be confident enough with the directionality of
movement of the machine, and should therefore not operate the machine near people or
obstacles.
ATTENTION: Work in slow movements to the right and left, possibly moving back so that the
operator always stands on an area of the floor yet to be cleaned up.
ATTENTION: Keep the power supply cable behind the operator, taking care not to operate the
machine in its vicinity in order not to damage it.
ATTENTION: Do not insist too much on the same area so as to avoid damaging the floor, also in
function of the type of brush or abrasive floor pad chosen.
ATTENTION: If you need to work in tight spaces you can turn the control column to the vertical
position.
8
7

AT THE END OF THE WORK

At the end of the work, and before carrying out any type of maintenance, perform the following operations:
1. Disconnect the plug (1) of the power supply cable (2) in the mains supply socket (3) (Fig.1).
ATTENTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
ATTENTION: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
2. Turn the handlebar to the vertical position, press the uncoupling lever (4) (Fig.2) and turn the
handlebar to the vertical position (Fig.3). When the handlebar is vertical, release the uncoupling
lever (4).
ATTENTION: During this operation, do not rest your foot on the appliance.
3
1
2
1
3. Tip back the machine and take the appliance to the place where it is maintained and carry out all
the procedures listed in the section
column "AT THE END OF THE WORK".
4. Once the maintenance work is finished take the appliance to the designated machine storage place.
ATTENTION: Park the machine in an enclosed place, on a flat surface; near the machine there
must be no objects that could either damage it, or be damaged through contact with it.
5. Lightly tip the machine back (Fig.4), block one of the rear wheels and shift the control column
backwards.
6. Turn the brush head into the vertical position (Fig.5).
7. Bring the rotated brush head into contact with the floor.
4
20
7
5
6
4
2 3
"RECOMMENDED PERIODIC MAINTENANCE" indicated in the
5