Tabla de contenido
Publicidad
INTRO PLAY (BY REMOTE CONTROL)
YOU CAN LISTEN THE BEGINNING (10 SECONDS) OF EACH TRACK IN A CD BY THIS FUNCTION & SAVING YOUR
TIME TO SEARCH THE DESIRE SONG
1)
PRESS "INTRO" BUTTON AFTER PLACING A CD INSIDE THE UNIT AT CD MODE
2)
SYSTEM START PLAYING THE FIRST 10 SECONDS OF EACH TRACK OF THE ENTIRE CD CONTINUOUSLY.
3)
PRESS "INTRO" BUTTON ONCE AGAIN IF IT REACH YOUR DESIRED TRACK FOR NORMAL PLAYBACK.
CD DISC PROGRAMMING
UP TO 20 TACKS CAN BE PROGRAMMED FOR DISC PLAY IN ANY ORDER. BEFORE USE, BE SURE TO PRESS
THE CD " STOP " BUTTON (3)
1.
SET IN CD MODE & STOP THE CD PLAYBACK.
2.
PRESS THE "MEM/PROG" BUTTON (4) , " PROG " WILL APPEAR ON LCD DISPLAY (1). MOREOVER, IT WILL
INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED.
3.
SELECT A DESIRED TRACK BY PRESSING SKIP
4.
PRESS THE"MEM/PROG" BUTTON (4) TO STORE THE TRACE INTO MEMORY.
5.
REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6.
WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS CD " PLAY/PAUSE " BUTTON (2) TO
PLAY THE DISC IN ASSIGNED ORDER.
7.
PRESS CD "STOP" BUTTON (3) TO TERMINATE PROGRAM PLAY.
DURING PROGRAM MODE, PRESS "MEM/CLK-ADJ" BUTTON (4) TO REVIEW THE TRACKS CURRENTLY
PROGRAMMED.
MP3 DISC PROGRAMMING
1.
FOLLOW THE SAME STEP 1 AND 2 AS CD PROGRAMMING PROCEDURE.
2.
SELECT A DESIRED ALBUM NUMBER BY PRESSING SKIP
3.
PRESS THE "MEM/CLK-ADJ" BUTTON (4) TO STORE THE SELECTED ALBUM INTO MEMORY, THEN PRESS
SKIP
OR
BUTTONS (9 OR 8) AGAIN TO SELECT THE TRACK NO. TO BE PROGRAMMED.
4.
REPEAT STEPS 2 AND 3 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY
5.
WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS CD " PLAY/PAUSE " BUTTON (2) TO
PLAY THE DISC IN THE ORDER YOU HAVE PROGRAMMED.
6.
PRESS CD "STOP" BUTTON (3) TO TERMINATE PROGRAM PLAY.
THE PROGRAMMING MODEL WILL AUTOMATICALLY STOP IF NO BUTTON IS BEING PRESSED IN A
PERIOD OF ABOUT 10 SECONDS AFTER PRESSING THE MEM/CLK-ADJ BUTTON (4).
PLAYBACK OF MP3 SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 FILE WHICH STORED IN THE MEMORY MEDIA WITH
USB CONNECTING PORT, MULTI- MEDIA CARD (MMC) OR SECURE DIGITAL (SD) MEMORY CARD.
1.
PRESS FUNCTION BUTTON (5) TO SELECT " UDISC " OR " SD/MMC " MODE.
2.
OPEN THE " USB/CARD SLOT COVER " (19)
3.
PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING INTO
COMPLETELY OR INSERT THE MEMORY CARD IN THE DIRECTION OF THE
ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE OF THE MEMORY CARD
SLOT COVER. INSERT STRAIGHT WITHOUT BENDING.
CONNECTING THE USB / MEMORY CARD UPSIDE DOWN OR BACKWARDS
COULD DAMAGE THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB /
MEMORY CARD). CHECK TO BE SURE THE DIRECTION IS CORRECT BEFORE
CONNECTION.
4.
THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND LCD
DISPLAY (1) WILL SHOW THE TOTAL NUMBER OF MP3 FILES AND TOTAL NUMBER OF ALBUM BEING
DETECTED.
5.
REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE
REMARK
-
THE SYSTEM CAN READ EITHER ONE OF THE STORAGE MEDIA ONLY. IF BOTH THE USB TYPE AND
MEMORY CARD TYPE STORAGE MEDIA HAVE BEEN CONNECTED, THE SYSTEM WILL READ THE MEMORY
CARD TYPE ONLY. OR THE ONE WHICH CONNECTING TO THE SYSTEM FIRST AT " CARD-USB " MODE
-
THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 FORMAT ONLY THOUGH THE USB
PORT/MEMORY CARD SLOT.
IF CONNECT TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3 ENCODING AND
-
TRANSFER, SOME FILES MAY NOT PLAY VIA THE USB SOCKET, IN THESE CASES PLEASE USE THE MP3
PLAYER CONNECTED TO THE AUX IN SOCKETS ON THE REAR OF THE UNITS, VIA THE CABLE SUPPLIED.
OR
BUTTONS (9 OR 8).
OR
BUTTONS (9 OR 8).
GB-4
Publicidad
Tabla de contenido
