Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
D) ALIGNING TOP LIEN OF REAR WALL TEMPLATE
CAUTION: WEAR GLOVES TO AVOID CUTTING FINGERS ON SHARP EDGES
1) Using tape measure, drawing a vertical line on the wall at the center of the 24" wide space.
2) Tape the rear wall template on the cabinet wall, align the center markers on the rear wall template to the
centerline on wall, making sure it is level and that the top line of the rear wall template is butted up against the
bottom edge of the upper cabinet.
3) According to the shape of the cabinet, the location of the rear wall template is compliant with the content C
"determining top line of rear wall template location under cabinet"
4) While taping the rear wall template on the wall draw circles on the wall at hole A, B, C (see illustration above /
actual plate marked with arrows). THREE HOLES MUST BE USED FOR MOUNTING. (If there are 2-wall studs
in right and left side based on center line FOUR holes must be used for mounting).
5) Remove the rear wall template and check the marking based on the actual mount plate (centerline, hole A, B, C).
6) Drill holes on the circle marks (A, B, C)
7) Drill a 3/16" hole at C for wood screw and two 5/8" holes at A, B for toggle bolts.
Note:
DO NOT MOUNT THE PLATE AT THIS TIME.
8) If the rear wall template is damaged or unusable, measure and mark the wall with the dimensions describe in step
E.
E) MARK REAR WALL OF THE CABINET WITHOUT REAR WALL TEMPLATE.
(423.8mm)
Moun�ng plate end hole(right/le�)
N O TE: I T I S V ER Y IM PO RTA NT TO
R E AD AND FO LLO W THE D IR ECTI O NS
IN TH E IN STA LLA TIO N IN STR U CTIO NS
B EFO R E P R OCE E DIN G W ITH TH IS
R E AR W ALL TE M PLATE.
T h i s
R e a r W
a l l T e m
p la t e
m o u n t i n g
p l a t e
n d to l o c a te t h e h o riz o n t a l e x h a u s t o u t le t .
a
1 . U s e a l e v e l
t o
c k t h a t
c h e
a c c u r a t e ly .
2 . L o ca te a n d m a r k
le a s t o n e
a t
o f
t h e
e n t e r
c
li n e .
L o c a te a n d m a r k
m o u n t i n g
p l a t e
IM P R OTA NT:
LO C A TE AT LEAS T O N E STU D O N EITH ER SID E O F
TH E C ENTE RLIN E.
M AR K TH E LO C A TIO N FO R 2 A DDITI O NA L, E VEN LY
S PAC E D TO G G LE
A R EA.
Tri m th e re a r wa l l te m p l ate a l o ng the do tt e d l i n e .
"
16
17/25
"
"
9/25
9
9/25
9
(237.8mm)
(237.8mm)
Bo�om edge Line of Moun�ng Plate
6 "
e r v e s
s
o p o s i ti o n
t
t h e
o tt o m
b
t h e
t e m p l a t e is
p o s it i o n e d
s t u d
n t h e l e f t o r
o
r ig h t s i d e
o le s t o
h
ig n w ith h o l e s in t h e
a l
.
Cent r linenotches
e
B O L T S I N THE M O U
NTING P LA T E
C
A
1. The Bo�om edge line of Moun�ng Plate must be 17
"
(435mm) from the Bo�om edge Line of Upper cabinet
1/8
17
and must be level.
(435mm)
2. Moun�ng plate end holes must be 16
the Bo�om edge Line of Upper cabinet must be on a
equal line with each other.They must each be 9 9/25
(237.8mm) from the center line.
12
B
Area E
"
(423.8mm) from
17/25
"
1/8
"
Publicidad
Tabla de contenido
