Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Installing Dust Bowl (Fig. F)
nOTE: It is very important that the filter is correctly
positioned before use.
1. Place filter assembly
2. Install the dust bowl
ensuring the housing tabs
bowl slots
15
as shown in Fig. F and rotate the dust
bowl counterclockwise to lock it firmly into position.
OPERATION (FIG. A)
WARNING:
Electric Shock – Use indoors only.
WARNING:
serious personal injury, turn unit OFF before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
WARNING:
Never use the vac without its filter.
Switching ON and OFF (Fig. D)
1. To turn the vac on, slide the ON/OFF switch
the "I" position.
2. To turn the vac off, slide the ON/OFF switch
to the "O" position.
3. Return the product to the charger immediately after use
so that it will be ready and fully charged for the next
use. Ensure that the product is fully engaged with the
charger plug.
Flip Up Brush (Fig. E)
1. A flip up brush
is built into the nozzle and can be
6
rotated upwards for use.
MAINTENANCE
WARNING:
serious personal injury, turn unit off and lock
off the tool before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning
WARNING:
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
Z87.1 approved eye protection when performing
this procedure.
7
into position inside the dust bowl.
4
onto the main housing
14
aligns with the main dust
To Reduce The Risk Of
To reduce the risk of
Projectile/Respiratory Hazard:
1
1
To reduce the risk of
Blow dirt and dust out of
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
3
,
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Emptying the Dust Bowl (Fig. F)
WARNING:
vacuum without both its filters.
iMPORTAnT: Maximum dust collection will only be
obtained with clean filters and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the dust bowl is full and requires emptying
To Empty the Dust Bowl (Fig. F)
1. Place the dust bowl over a trash bin and remove the dust
bowl
4
bowl
4
the main housing.
2. Remove the filter assembly
dust bowl
3. Shake or lightly brush any dust from the filter assembly.
forward to
4. Empty the dust from the dust bowl
and wash if necessary. Ensure that the dust bowl is
backward
completely dry before using.
5. Place filter assembly
6. Install the dust bowl
ensuring the main housing tabs
bowl slots
bowl counterclockwise to lock it firmly into position.
Cleaning the Filters (Fig. F, G)
Removing Pre‑filter
1. Place the dust bowl over a trash bin and remove the dust
bowl
4
bowl
4
away from the main housing.
2. Remove the filter assembly
dust bowl.
3. Twist counterclockwise and pull the pre-filter
seperate it from the filter
4. Remove the pre-filter and shake or lightly brush any dust
from the filter and pre-filter.
5. Empty any dust from the dust bowl
and wash if necessary. Ensure that the dust bowl is
completely dry before using.
6. Wash the pre-filter
soapy water. Ensure that both are completely dry for 12
hours before using.
7. Install the pre-filter onto the filter, ensuring the filter
slots
17
pre-filter clockwise to lock it firmly into position.
8. Install the filter assembly into the dust bowl.
Never use solvents or other
Never use this cordless hand
from the main housing
3
clockwise and pulling the dust bowl away from
7
by pulling it out of the
4
.
7
into position into the dust bowl.
4
onto the main housing
14
15
as shown in Fig. F and rotate the dust
from the main housing
3
counterclockwise and pulling the dust bowl
7
by pulling it out of the
9
.
8
and filter
9
align with the pre-filter tabs
English
by twisting the dust
4
into a trash bin
3
,
aligns with the dust
by twisting the dust
8
to
4
into a trash bin
regularly using warm,
18
and rotate the
7
Publicidad
Tabla de contenido
