How The Controls Work; Troubleshooting Guide - Good Earth Lighting SE1295-BRS-02LF1-G Manual De Instrucciones

1
2
indicator will blink twice to let you know it has reset the dusk level. To return to the default setting, push the Dusk Learn for
around 3 seconds and the red LED indicator will blink twice to indicate that you have returned to the default setting.
PROBLEM
Security light
1. Batteries are defective or depleted.
does not come
2. Batteries are installed wrong.
on.
3. Battery compartment cover is loose.
4. It is daylight.
5. Movement is taking place outside of
the motion sensor detection area.
6. Button is set to O .
Light
1. Light sensor is triggered by reflected
continuously
light from the security light itself.
cycles ON and
2. Heat is being reflected from other sources
OFF (strobe
and may be triggering sensor on and o .
e ect).
Light turns on
1. Light may be installed in shadows/dark
during daylight
area.
hours.
Light comes on 1. Sensor may be triggered by a small
for no apparent animal or passing car.
reason.
2. Hot air (dryer vent, car exhaust, etc.)
may be triggering the sensor.
Light stays on
1. Motion sensor may be picking up a
continuously at
continuous flow of warm air from an air
night.
vent, dryer vent, or heat reflecting o a
surface.
REPLACEMENT PARTS LIST: Hardware Kit:ZH-SE1295F02
Need Help?
Good Earth Lighting
Good Earth Lighting
6

How the Controls Work

ROTARY KNOB
O : Select O to completely switch o the device.
Auto: This is the normal Automatic motion sensing mode. The light will stay on as
long as the fixture detects motion. After the fixture no longer senses motion, it will
turn o after 20 seconds.
ES: This is energy-saving mode. When motion is detected, the light turns on at
70% brightness for 20 seconds. When the fixture no longer senses motion, it will go
to 20% brightness. Then the light will turn o completely after 40 seconds.
DUSK LEARN BUTTON
The light is preset to work only after dusk. If you want the light to work at a predetermined
"dusk" time, then you need to set it using the Dusk Learn button.
Press the Dusk Learn button once to recalibrate the dusk level to the current light level. The
motion sensor will now activate at this light level from now on. If you want the light to work
day and night (regardless of the light level), push the Dusk Learn button while the fixture is
outdoors during the day, or hold the fixture up to a light source and push the Dusk Learn
button. Motion will turn the light on, day or night, regardless of the light level; the red LED

Troubleshooting Guide

POSSIBLE CAUSE
Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
®
is a registered trademark of Good Earth Lighting, Inc. © 2022 Good Earth Lighting, Inc. REV08.22
®
CORRECTIVE ACTION
1. Replace the batteries.
2. Reinstall the batteries correctly.
3. Check battery compartment cover to ensure it
is closed and secured with the screw.
4. Light is operating as it was designed. Recheck at night or
move fixture to a darker area.
5. Move fixture within the desired detection area.
6. Set dial to "Auto" or "ES."
1. Change the position of the light heads, aiming
light away from the reflecting surfaces.
2. Remove heat source from detection zone or
move fixture to new location.
1. Press the Dusk Learn for around 3 seconds to go back to
factory setting.
1. Light is operating as it was designed.
2. Remove heat source from detection zone or move
fixture to new location.
1. Remove heat source from detection zone or move
fixture to new location.
Printed in China