Cleaning Your Headphones; Headphone Software Updates; Power Cycle And Reset; Power Cycle - Bowers & Wilkins Px7 S2 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 23
Device Management
Toggle Auto standby on to place the headphones
into a power-saving state after 15 minutes of
inactivity.
Toggle Wear sensor on to enable intelligent
playback control; lift an earpiece or remove your
headphones to pause playback. Place them back on
your ears to resume playback.
Rename product
Tap Rename product to choose a new Bluetooth
name for your headphones. Note that devices
already paired with the headphones may still
reference the previous name.

8.3 Headphone Software Updates

Bowers & Wilkins will occasionally make available
software updates that refine and optimise the
performance of your headphones or add new
features. The Bowers & Wilkins Music app will notify
you when a software update is available. Tap on the
notification and then follow the in-app instructions.

9. Power Cycle and Reset

The reboot/reset process may generate noise
in the headphones – do not wear during this
process.

9.1 Power Cycle

To reboot your Px7 S2, remove the headphones
from your head and remove any cables from the
headphones. Simultaneously hold the Volume +
and Volume - buttons for 10 seconds until the
indicator LED extinguishes. Release the buttons
when the indicator lights up again. Rebooting your
headphones will not reset their internal settings or
clear the paired device history.

9.2 Factory Reset

You can clear the paired device history and restore
all settings to their factory defaults. Remove the
headphones from your head and remove any cables
from the headphones. With Px7 S2 powered on,
simultaneously hold the Volume +, Volume - and left
earpiece Quick Action button for 10 seconds until
the indicator LED extinguishes. Release the buttons
when the indicator lights up again; the headphones
will be ready to pair to a device. Alternatively, you
can perform a factory reset from the headphone's
settings page of the Bowers & Wilkins Music app.
10. Care & Maintenance

10.1 Storing Your Headphones

Taking care of your Px7 S2 will ensure they continue
to deliver the best performance and experience.
When you are not using your headphones,
stow them in the included storage pouch. It is
recommended the headphones are first powered off.
1. Retract the headband on each side so they are
in the smallest position.
2. With the buttons facing you, rotate the
earpieces inwards so they lay flat.
3. Place the headphones into the storage case.

10.2 Cleaning Your Headphones

It is advised that you clean your headphones
regularly. Your Px7 S2 can be cleaned by a soft,
damp microfiber cloth, gently wipe or dab clean.
The fabric on Px7 S2 has been specially coated with
moisture and stain repellent. If dirt, stain or fibre
residue accumulate on the fabric surface, please
clean as instructed above.
• Do NOT aggressively rub or use an abrasive
tool to clean, especially the fabric or leather.
• Do NOT use paper towels, napkins or tissue as
they will leave residue.
• Do NOT use cleaning detergents, soapy water,
polish or chemical cleaners.
• Ensure that no moisture get inside the
earpieces, buttons and interface ports.
11. Support
Should you require further help or advice regarding
your Px7 S2, please visit the Bowers & Wilkins
support site: www.bowerswilkins.com/support.

11.1 Environmental Information

This product complies with international directives,
including but not limited to the Restriction of
Hazardous Substances (RoHS) in electrical and
electronic equipment, the Registration, Evaluation,
Authorisation and restriction of Chemicals (REACH)
and the disposal of Waste Electrical and Electronic
Equipment (WEEE). Consult your local waste
disposal authority for guidance on how properly to
recycle or dispose of this product.
7

Publicidad

Tabla de contenido
loading

Tabla de contenido