VONROC EH516AC Traducción Del Manual Original página 8

EN
• Timer button (2M): The timer can be set bet-
ween 1 hour and 9 hours. The display will show
the duration currently set. Press the timer but-
ton (2M) to set the timer with 1 hour intervals.
The timer indicator (2L) will light up. Without
a timer there is no limit.
• Light button (2A): Press the light button to
change the colour of the ambient light. Cycles
between blue, red, purple and off.
Functions of the remote control (Fig. F)
In addition to the before mentioned control panel
operation, the heater can also be operated by the
remote control (9). The available functions are:
• Temperature increase button (9F): Press to
increase the desired ambient temperature.
• Temperature decrease button (9G): Press tode-
crease the desires ambient temperature.
• On/off button (9A): Turns the heater on and off.
• Mode button (9B): Cycles between fan, low and
high heating.
• Fan: The fan indicator (2I) will light up.
• Low heating mode – 1300W: the low heating
indicator (2H) will light up.
• High heating mode – 2000W: the high hea-
ting indicator (2G) will light up.
• Oscillation button (9D): Press the oscillation
button to activate the heater to swing. The os-
cillate indicator (2K) will light up. Press it again
to deactivate.
• Timer button (9C): The timer can be set
between 1 hour and 12 hours. The display
shows flashing the duration currently set for 5
seconds. Press the timer button to set the timer
with 1 hour intervals. The timer indicator (2L)
will light up. Without a timer there is no limit.
• Ambient light on/off (9E): Press the light button
to change the colour of the ambient light. Cy-
cles between blue, red, purple and off.
WIFI-operation
In addition to the before mentioned manual and
remote operation, the heater can also be operated
remotely over a WiFi network using your smart pho-
ne or tablet. The required app can be downloaded
and used free of charge.
Downloading the app to your phone or tablet
(Fig. G)
• Scan the QR-code (Fig. G) on your phone or ta-
blet to download and install the "Smart Life" app.
8
• If you can't or don't want to use the QR-code
you may also install the app manually. To do
this, visit the Google Play Store or Apple App
Store on your phone or tablet. Search for the
"Smart Life" app (Fig. G).
• After the app has been installed you will need
a "Smart Life" account to login. If you do not
yet have an account, you may create one (free
of charge) by tapping the 'Register' button in
the app.
Pairing your heater with the "Smart Life" app
(Fig. H, I)
• Put the heater into stand-by mode and hold on
the On/Off button (2F) for 5 seconds. The WIFI
status indicator (2D) will start flashing.
• While the WiFi status indicator is flashing, open
the app on your phone or tablet and press Add
a Device.
• The app will search for nearby devices. If the
heater does not appear you can add it manually.
Select the device type, in this case Small ap-
pliances -> Heater. Confirm in the app that the
WiFi status indicator on the heater is flashing.
• You will be prompted by the app to select a WiFi
network and enter the WiFi password. The app
will send these details to the heater, allowing
the heater to establish a connection to your
WiFi network.
Using the "Smart Life" app (Fig. J)
The "Smart Life" app can be used to control many
different devices. The status of each device is dis-
played on the device list. The following states are
possible for the heater:
• Offline (The device is not powered, or not con-
nected to the WiFi network).
• Turned Off (Power and network connection are
available, heating is currently disabled).
• Turned On (Power and network connection are
available, heating is enabled).
When the heater is online (either Turned Off or
Turned On) tap the device name in the app to open
the control interface.
Note: when the heater is offline you will not be able
to open the control interface.
• Use the Mode button to change the operating
mode of the heater. The available modes are:
WWW.VONROC.COM