Operating - VONROC EH516AC Traducción Del Manual Original

L. Timer indicator
M.Timer button
N. Temperature
3. Air outlet grille
4. Base
5. Ambient light
6. Handle
7. Air inlet
8. Main switch
9. Remote control
A. On/off button
B. Mode button
C. Timer button
D. Oscillation button
E. Ambient light on/off
F. Temperature increase button
G. Temperature decrease button
10. Temperature increase button
11. Temperature decrease button

3. OPERATING

Check the device for damage before use
and only use in good working condition.
When using the heater for the first time, you may
notice a slight emission of smoke. This is quite
normal and it stops after a short time. The heating
element is made of stainless steel and was coated
with protection oil by production. The smoke is
caused by the left oil when heated.
Placing the electric heater (Fig. B, C, D)
• Dismount the screw (Fig. B).
• Put the base together (Fig. C). Attach the base
to the heater (Fig. D). Make sure that the holes
in the base correspond to the protruding parts of
the heater. To avoid damage, put the heater on
a soft and clean blanket.
• Mount the screw (Fig. D).
• Place the heater upright on a firm and a level
surface.
• Keep a minimum distance of 1 m between the
front of the housing and walls, and 30 cm from
all other housing surface areas. Keep away from
wet environments.
Warning! Make sure to place the heater in
a safe spot, so you cannot easily trip over
the machine and cable. Make sure to place
the heater where it cannot fall down / of.
WWW.VONROC.COM
Starting the electric heater (Fig. A, E, F)
• Plug in the cable to the mains power outlet.
• Turn the main switch (8) on.
• Press the on/off button (2F, 9A) to start the
heater. The default heating mode is fan, the fan
indicator (2I) will light up. Press de mode button
(2E, 9B) to change the heating mode.
• Fan: The fan indicator (2I) will light up.
• Low heating mode – 1300W: the low heating
indicator (2H) will light up.
• High heating mode – 2000W: the high hea-
ting indicator (2G) will light up.
Adjusting the temperature (Fig. A, E, F)
• By default, the ambient temperature is shown
on the display.
• By default, the temperature is 23 ⁰C. The tem-
perature can be set between 15 ⁰C and 40 ⁰C.
• Set the temperature as desired by press the
temperature button (2B).
• The target temperature will keep flashing for
3 seconds after the last button press, then the
display will show the ambient temperature.
Constant room temperature
The heater starts and stops automatically to keep
the room temperature constant. Once the ambient
temperature in the room reaches the desired target
temperature, the heating element will be in standby
mode. Once the ambient temperature starts to decre-
ase, the heating element will be switched on again.
Functions of the control panel (Fig. E)
The heater can be operate by the control panel (2).
The available functions are:
• Temperature button (2B): Press to increase
the desired ambient temperature. When the
maximum of 40 ⁰C is reached, it will start again
at 15 ⁰C.
• On/off button (2F): Turns the heater on and off.
• Mode button (2E): Cycles between fan, low and
high heating.
• Fan: The fan indicator (2I) will light up.
• Low heating mode – 1300W: the low heating
indicator (2H) will light up.
• High heating mode – 2000W: the high hea-
ting indicator (2G) will light up.
• Oscillation button (2J): Press the oscillation
button to activate the heater to swing. The os-
cillate indicator (2K) will light up. Press it again
to deactivate.
EN
7