Scheppach HS120o Traducción Del Manual De Instrucciones Original página 24

12. Avoid abnormal posture
- Make sure that you have secure footing and
always maintain your balance.
- Avoid awkward hand positions in which a sudden
slip could cause one or both hands to come into
contact with the saw blade.
13. Take care of your tools
- Keep cutting tools sharp and clean in order to be
able to work better and more safely.
- Follow the instructions for lubrication and for tool
replacement.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
- Keep the handle dry, clean and free of oil and grease.
14. Pull the connector out of the socket
- Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
- When the electric tool is not in use or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
15. Do not leave a tool key inserted
- Before switching on, make sure that keys and
adjusting tools are removed.
16. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
17. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
18. Remain attentive at all times. m Pay attention to
what you are doing. Remain sensible when working.
Do not use the electric tool when you are distracted.
19. Check the electric tool for potential damage
- Protective devices or other parts with minor
damage must be carefully inspected to ensure
that they function correctly and as intended prior
to continued use of the electric tool.
- Check whether the moving parts function
faultlessly and do not jam or whether parts are
damaged. All parts must be correctly mounted
and all conditions must be fulfilled to ensure fault-
free operation of the electric tool.
- The moving protective hood may not be fixed in
the open position.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specified
in the operating manual.
- Damaged switches must be replaced at a
customer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any electric tool on which the switch
cannot be switched on and off.
24 | GB
20. ATTENTION!
- Exercise elevated caution for double mitre cuts.
21. ATTENTION!
- The use of other insertion tools and other
accessories can entail a danger of injury.
22. Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable
safety
performed by an electrician using original spare
parts. Otherwise accidents can occur.
23. Do not use the cable for purposes for which it is
not intended.
- Do not use the cable to pull the plug out of the
outlet. Protect the cable from heat, oil and sharp
edges.
Additional safety instructions, safety precautions
• Warning! Do not use damaged, cracked or
deformed saw blades.
• Replace a worn table insert.
• Only use saw blades recommended by the
manufacturer which conform to EN 847-1.
m Warning! When changing the saw blade, ensure
that the cutting width is not smaller and the width of
the saw blade disc is not greater than the thickness
of the riving knife!
• Make sure that a suitable saw blade for the material
to be cut is selected.
• Wear suitable personal protective equipment. This
includes: Hearing protection to reduce the risk of
hearing loss, respiratory protection to reduce the
risk of inhaling hazardous dust.
• Wear gloves when handling saw blades and rough
materials.
• Carry saw blades in a container whenever practical.
• Wear protective goggles. Sparks created during
work or fragments, chippings and dust ejected by
the device can case sight loss.
• Connect a dust collecting device to the electric
tool when sawing wood. The emission of dust
is influenced, among other things, by the type of
material to be processed, the significance of local
separation (collection or source) and the correct
setting of the hood/guide plates/guides.
• Do not use saw blades made of high-speed alloy
steel (HSS steel).
• Always keep the push stick or wooden push block
in its holder on the electric tool when not in use.
www.scheppach.com
regulations. Repairs may only be