Cleaning, Maintenance; Cleaning & Maintenance; Tips And Tricks; Accessories - Metabo STEB 70 Quick Manual Original

17026919_0909 STEB 70 Quick STEB 80 Quick.book Seite 14 Montag, 14. September 2009 4:43 16
ENGLISH
ENG

9 Cleaning, Maintenance

Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Clean the saw blade clamping fixture regularly and
thoroughly by blowing with compressed air.
If necessary, clean the openings behind the saw
blade support roller (2).
Apply a drop of oil to the saw blade support roller
(2) from time to time.

10 Tips and Tricks

Sawing different materials
When sawing metal, lubricate the saw blade with a
Metabo lubricating stick. Wet the cutting line with
water when sawing plexiglas. Saw metal sheets
less than 1 mm thick on a wooden base.
Curved cuts
When making curved cuts, we recommend using
narrow, specially designed saw blades.
Plunging
The jigsaw blade can plunge into workpieces
made from thin, soft materials without the neces-
sity of drilling a hole beforehand. Only use short
saw blades. Only at 0° angle setting.
See illustration on page 3. Set the adjustment lever
(7) to position "0" (pendulum motion is switched
off). Position the jigsaw with the front edge of the
footplate (5) on the workpiece. Hold the operating
jigsaw firmly and guide slowly downwards. Once
the saw blade has penetrated the workpiece, the
pendulum motion can be activated.
In thicker workpieces, a hole for inserting the saw
blade must be drilled first.

11 Accessories

Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.
A Saw blades with single lug bayonet shank.
Use a saw blade that is suitable for the mate-
rial being sawn.
B Anti-splintering footplate insert (replacement)
C Protective plate for attaching to the jigsaw
footplate. The protective plate prevents work-
14
All manuals and user guides at all-guides.com
For complete range of accessories, visit
www.metabo.com or refer to the main catalogue.
11.1 Attaching the circular-cutting and par-
For sawing circles (dia. 100 - 360 mm) and making
cuts parallel with edges (max. 210 mm).
Attaching clamping elements (page 4, Fig. I)
Place the clamping elements (a) on the footplate
(5) with the opening facing forwards and the
threaded hole facing up. Insert the screws (b) from
underneath.
(10) may be damaged when diagonal cuts are
made.
clamping fixture (10).
Attaching the circular-cutting guide (page 4,
Fig. II)
- Slide the rod on the circular-cutting and parallel
- Set the desired radius (d).
- Tighten the screws (b).
Attaching the parallel guide (page 4, Fig. III)
- Slide the rod on the circular-cutting and parallel
- Unscrew the centre point (c).
- Set the dimension (e)
- Tighten the screws (b).
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
pieces with sensitive surfaces from becoming
scratched.
D Guide fixture for using the jigsaw with the
guide rail
E Guide rail (overall length: 1500 mm)
F Connector for easy joining of 2 guide rails
6.31213
G Clamps for securing the guide rail to the work-
piece or work bench
H Jigsaw bench with clamp for securing to the
work bench
I Flexo 500 universal table for stationary use of
Metabo jigsaws, etc.
J Table extension
K Lubricating stick for lubricating the saw blades
when sawing metal.
L Extraction hose
M Circular-cutting and parallel guide
allel guide
Remove the clamping elements after use
otherwise the saw blade clamping fixture
At a 45° diagonal cut angle, tilting the jigsaw
to the right will damage the saw blade
guide sideways into the clamping elements (a)
(centre point (c) faces downwards).
guide sideways into the clamping elements (a)
(centre point (c) faces upwards).

12 Repairs