Manuales relacionados para Truper TPN-734H-2K
Resumen de contenidos para Truper TPN-734H-2K
- Página 1 Manual Air impact wrench kit 1/2” Applies for: Model Code TPN-734H-2K 18281 TPN-734H-2K Use oil continuously and WARNING dosed to lubricate the tool. Read this manual thoroughly CAUTION before using the tool.
-
Página 2: Tabla De Contenido
Manual before using the tool. Parts Assembly Keep this manual for future references. Start Up The illustrations in this manual are for reference only. They might be different from the real tool. Maintenance Notes Authorized Service Centers Warranty Policy TPN-734H-2K ENGLISH... -
Página 3: Technical Data
Technical Data TPN-734H-2K Code 18281 Description Air impact wrench kit Impact Mechanism Twin Hammer Box Impeller 1/2” Screws Capacity 3/4” Maximum Torque 400 lb-ft Air Ejection Head on Noise Level 115 dB Vibration > 2.5 m/s Free speed 7000 RPM Weight Without Accessories 5.7 lb... -
Página 4: General Safety Warnings For Pneumatic Tools
General Safety Warnings for Pneumatic Tools Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. In normal conditions, the risk of Never use the tool in explosive areas or in the presence injury is reduced. -
Página 5: Risk Control When Using Pneumatic Tools
Risk Control When Using Pneumatic Tools Risk of injury in head and eyes To prevent head and eyes injuries WARNING • Compressed air out of pneumatic • Always, when operating pneumatic equipment wear equipment may be dangerous. Objects like brackets, burrs, protection glasses in compliance with the ANSI Z87.1 splinters, dust and other residues may be impelled towards Standard. -
Página 6: Risk Of Injuries
Risk Control When Using Pneumatic Tools Risk of injuries To prevent injuries WARNING • Damaged hoses may burst and cause • Do not abuse the hose or the connectors. serious injuries or deafness. • Keep the hose away from sharp or abrasive edges. •... -
Página 7: Parts
Parts Impeller Air and Surplus Trigger Oil Exhaust Torque Selector (also Rotation Selector) Handle Air Inlet 1/2” x 5” Box Extension 10 dies for 1/2” impellers • 3/8” • 11/16” • 7/16” • 3/4” • 1/2” • 13/16” 0,41 fl Oz •... -
Página 8: Assembly
Assembly Die Set Up • Disconnect the tool from the air outlet before replacing the die. Nut or • Select the die you need and set it in the box impeller. Lug Inlet • Always use impact dies with this tool. Do not use dies for hand tools. -
Página 9: Start Up
Start Up Air Outlet Connection CAUTION • We recommend using fast couple hoses to easily get them connected to the included nipple. This way it can be connected and Plastic disconnected tools fast and interchange easily. Air Inlet • Remove the plastic cap covering the air inlet in the handle base. •... -
Página 10: Maintenance
Maintenance Lubrication Service • Pneumatic tools need constant lubrication along their • Servicing the tool shall be carried out every 3 months useful life and during the operation. The compressed air only in a Authorized Service Center. needed in the tool to run carry humidity which could Service and maintenance carried out by not certified oxidize the motor and bearing in the tool. -
Página 11: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers (800) 690-6990 or 01 (800) 018-7873 to get information about the nearest Authorized Service Center. -
Página 12: Warranty Policy
. Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.