NAVEE S65 Manual Del Usuario página 11

9. Care & Maintenance
EN
Inflate the Tire
Check the tire pressure every month, and inflate the tires
if the pressure is too low. The recommended tire pressure
is 45 psi.
If there is a lack of air in the front and rear tires, you
may use the extended nozzle supplied with the scooter
to inflate tires. First connect the extension nozzle with
air pump, then unscrew the front (rear) tire valve cap,
and connect the extension nozzle and the valve securely
together, then Inflate the tire.
WARNING! Tire removal is very complicated. Please do
not remove the tire by yourself. Improper operation
may affect the operation of the scooter. Please contact
professional support.
Adjust the Disc Brake
Tool: 4 mm hex key (the tool needs to be prepared
by the user).
Before adjusting, make sure the scooter is turned
off and not being charged. During adjusting, pull
the end of the brake line to make the line tight.
Note: If the brake is too tight, use the tool to loosen
the screw by turning it counterclockwise, pull the
disc brake rocker arm outwards, and then tighten
the screw. If the brake is too loose, use the tool to
loosen the screw by turning it counterclockwise,
push the disc brake rocker arm forwards, and then
tighten the screw.
WARNING ! As with any mechanical component, a vehicle is subject to high stresses and wear. The various materials
and components may react differently to wear or fatigue. If the expected service life for a component has been
exceeded, it may break suddenly, therefore risking causing injuries to the user. Cracks, scratches and discoloration
in the areas subject to high stresses indicate that the component has exceeded its service life and please contact an
authorized or a specialized repairer.
16
Valve Cap
Disc Brake
Rocker Arm
Adjusting
Screw
10. Specifications
Name
Product
Model
Vehicle: L × W × H [1]
Dimensions
After Folding: L × W × H
Net Weight Vehicle Net Weight
Load Range
Rider Age
Body Length
Max. Speed
General Range [2]
Max. Climbing Angle
Suitable Surfaces
Assembled Electric
Scooter
Operating Temperature
Storage Temperature
IP Rating
Charging Time
Model
Nominal Voltage
Max. Charge Voltage
Rated Energy
Battery Pack
Intelligent Battery
Management System
Normal Charging
Temperature Range
Rated Capacity
Wheel Motor Rated Power
Output Power
Input Voltage
Battery Charger Max. Output Voltage
Rated Output
[3]
Model
Tire Front & Back Tires
Frequency Band
Bluetooth
Max. RF Power
[1] Vehicle height: From the ground to the top of the scooter
[2] General range: Measured when there is no wind and at 77 ° F (25 ° C), the scooter is fully charged to ride at a constant speed of 9.3 mph (15
km/h) on a flat surface with a load of 165.3 lbs (75 kg）
[3] To recharge the battery, only use the battery charger provided in the package. Please see battery charger parameters in Specifications.
NAVEE Electric Scooter S65
NKP2223-B32
48.1 × 21.7 × 49.8 in (1222 × 551 × 1266 mm)
48.1 × 21.6 × 21.2 in (1222 × 549 × 539 mm)
53.6 lbs (24.3 kg)
55.1 - 264.6 lbs (25–120 kg)
16–50 years
3'11"–6'6"(120–200 cm)
19.9 mph (32 km/h)
Approx. 40.4 miles (65 km)
Approx. 25%
Cement or asphalt road, with benches of less than 1 cm or crevices narrower
than 3 cm
14–104 ° F (-10 to 40 ℃）
-4–113 ° F (-20 to 45 ℃）
IP55
Approx. 6.5 h
P2301-BD5A
46.8 V
54.6 V
596.7 Wh
Over-heating, short circuit, over-current, over-discharge, and over-charge
protection
32–104 ° F (0 to 40 ℃）
12.75 Ah
500 W (0.5 kW)
121.9 W (0.1219 kW)
100–120 V~
54.6 V
53.0 V 2.3 A
S126BP5300230U
Tubeless self-sealing tires, φ250 × 64 straight valve, with the materials of
natural carbon black and synthetic rubber
2.4000–2.4835 GHz
8 dBm
EN
17