Additional Functions - Vollrath STOELTING SCBA118-37 Manual Del Propietário

S B C A & S C B F
Product Preservation Icon (F):
If it is on, it shows that the machine is in the Product
Preservation mode.
Granita Making Icon (G):
If it is on, it shows that the machine is in the Granita Making
mode.
Density Bar (H):
It shows the set density value and the alarms.
How To Start The Dispenser:
Turn the main power switch to position I. Pilot light (A) hopper
will be illuminated, showing that the dispenser is ready to work.
Keep button (B) pressed until the dispenser starts.
Select the operation mode and the desired product density by
using keys (C) or (D).
Compressor Icon (E):
It shows the condition of the cooling solenoid valve.
Icon off: Solenoid valve closed.
Icon flashing: Delay timer on.
Icon on: Solenoid valve open.
Product Preservation Icon (F):
If it is on, it shows that the machine is in the Product
Preservation mode.
Granita Making Icon (G):
If it is on, it shows that the machine is in the Granita Making
mode.
Density Bar (H):
It shows the set density value and the alarms.
Current Time (L):
Displays the current time and/or product temperature.
°C/°F Scale Icon (M):
The temperature scale is set to (°C or °F)
Timer Icon (N):
When this symbol is lit, the timer is operating.
Timer
DAY/NIGHT TIMER
This control board has a clock module which is used to auto-
matically switch from day mode to night mode and vice versa at
preset times.
NOTE: On machines with multiple bowls, the timer is only
present on the right control and its settings apply to
all bowls.
When the machine is in Standby, the current time is displayed
with two flashing points separating the second and third digit to
indicate the seconds. The current time and the mode switching
times can only be set when the machine is in Standby mode
using the following keys:
Setting of current time and temperature scale (°C/°F) Key B +
Key C.
Setting of mode switching time intervals Key B + Key D
Timer ON/OFF Key D pressed for 5 seconds.
figure 3
SETTING OF CURRENT TIME
Press keys B and C simultaneously to enter the current time
setting mode. Press keys C and D to make the individual
settings and press key B to conform and move on to the next
selection. The following must be set in this order:
1 The number 24 or 12 are displayed and the second two
digits flash.
2 Setting of current time. The first two digits flash as well as
the third or fourth digit if the 12 hr mode is selected.
3 Setting of minutes.The second two digits flash.
SETTING OF MODE SWITCHING TIME INTERVALS
Press keys B and D simultaneously to enter the switching time
interval setting mode. The setting always starts from 00:00 and
the first time with the day mode, indicated by a lit G icon. Press
keys C and D to increase or decrease the time shown on the
display by intervals of 15 minutes and press key B to modify the
operating mode from day to night and vice versa. To adjust the
intervals, you must select whether the machine should be in
night or day mode at 00:00 by pressing key B and then press key
C until you reach the time you want to change mode. Now press
key B to switch mode and the icon comes on to indicate that the
mode has changed. Scroll backwards and forwards using keys
C and D to check the switching time intervals. You can set mode
switching for every 15 minutes. When you reach 23:45 press
key C again to quit the switching time interval setting.
If the 12 hr mode has been selected, A or P is indicated on the
third or fourth figure (denoting AM or PM).
TIMER ON/OFF
If you press key D for 5 seconds when the machine is in Standby
mode, the day/night timer is activated. The icon N indicates the
state of the timer. The default value the first time the machine is
switched on is timer OFF.
NOTE: The keypad lock also has affects the Standby mode
and therefore the possibility of adjusting the clock.
TEMPORARY SUSPENSION OF TIMER
When the timer is activated and the machine is operating in Day
Mode, the timer can be temporarily suspended so that the
operating mode can be manually adjusted. To do this, hold
down the night key for two seconds, when the timer icon flashes
you can select the Night Mode or Cleaning on any bowl. Press
the day key again to reactivate the timer.

6. 2 ADDITIONAL FUNCTIONS

LIGHT SWITCHING ON/OFF
By pressing key standby (B) twice quickly, lights can be turned
on and off. When the machine is in the Granita Making mode,
lights are always on; when the machine is in the Product Preser-
vation mode, lights are always off.
DENSITY ADJUSTMENT
When the machine is working in the Granita Making mode, it is
possible to adjust product density by pressing keys C or D
briefly.
The factory set value is 5, which is recommended to make gra-
nitas.
6