To Use The Drive On The Wheels; High Load Function - Husqvarna LC 247i Manual De Usuario

LED display
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To start the product (LC 247i)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 31)
4. Stay behind the product.
5. Loosen the start inhibitor. (Fig. 18)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 32)
To start the product (LC 347iVX,
LC 353iVX)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 33)
4. Stay behind the product.
5. Push the ON/OFF button (A) on the control panel.
The display comes on. The battery indicator (B)
shows the battery charge of the 2 batteries. The
number of the battery that operates is shown
adjacent to the battery indicator. For models
LC 347iVX, LC 353iVX, the display also shows the
set speed. (Fig. 34)
6. Loosen the start inhibitor. (Fig. 35)
7. Push the motor brake handle in the direction of the
handlebar. (Fig. 36)

To use the drive on the wheels

LC 347iVX, LC 353iVX
• Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 37)
• Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 38)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE
The product has a battery saving function (SavE
gives longer operation time.
16
Charging status
50%-75%
75%-100%
Fully charged
™
function (LC 247i)
• Push the SavE
function. (Fig. 39)
• Push the SavE
function.
Note:
The SavE
ground conditions make it necessary to have a higher
output. The SavE
when the ground conditions let it.
To use the SavE
(LC 347iVX, LC 353iVX)
The product has a battery saving function (SavE
gives longer operation time.
1. Push the SavE
™
SavE
2. Push the SavE
The SavE
40)
Note:
The SavE
ground conditions make it necessary to have a higher
output. The SavE
when the ground conditions let it.

High load function

When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
Motor stalling
During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product restarts
automatically. If the product does not restart in 5-10
seconds, it can be necessary to clean below the cutting
cover. Refer to
™
) that
™
button to position 1 to start the
™
button to position 0 to stop the
™
function stops automatically if the
™
function starts automatically again
™
function
™
button (A) to start the function. The
symbol (B) on the display comes on.
™
button again to stop the function.
™
symbol (B) on the display goes out. (Fig.
™
function stops automatically if the
™
function starts automatically again
To clean the product on page 18 .
WARNING:
If the motor stops, the
product tries to restart automatically for 5-10
seconds. Wait for a minimum of 15 seconds
before you do a check of the cutting cover.
WARNING:
Before a check of the
cutting cover, release the motor brake
handle, turn the safety key to 0, remove
the battery and wait for a minimum of
5 seconds. There is a risk of injury if
the obstacle is removed and the product
accidentally starts.
1696 - 004 - 14.11.2022
™
) that