Chapin 19099 Manual De Instrucciones

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave
a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer's original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
6-8136
Valve Kit
Kit de la válvula
Ensemble de soupape
6-6092
Hose Black
Manguera para trabajos pesados Negro
Tuyau pour service intense Noir
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
6-8301
.8 GPM Nozzle Assembly
6-5373
Conjunto de boquilla de .8 GPM
Holster
Assemblage de buse .8 GPM Funda
Étui
6-4646
Repair Parts Kit Gaskets and Seals (not included)
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus)
19099
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
1. Hose to Tank
1A
Attach the hose by screwing the swivel
nut clockwise and tightening to 37 in. lbs.
Refer to Pre-use check before using.
2. Extension wand and Nozzle Assembly
Shut-off to wand to nozzle assembly
2A
Metal
Rod
Sk-1154-1
Shut-off to nozzle assembly
2B
Metal Rod
To attach nozzle directly to shut-off, unthread brass extension nut and metal rod. Assemble valve
seat (included), nozzle adapter and nozzle to the shut-off as shown in figure 2C. Note orientation of
valve seat. It will leak if assembled incorrectly.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace
hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for
signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and
could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and
replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes
and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these
conditions are found, replace affected part with original manufacturer's part before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
5. Pressurizing and Spraying
5A 5A 5B 5B
017670 (A) R0421
Nozzle
Brass Extension
Nozzle
Brass
Adapter
Extension Nut
The dripless shut-off comes
assembled as shown in figure 2A.
Metal Rod
2C
Valve Seat
Nozzle
Nozzle Adapter
TO LOCK HANDLE: Push handle down
to depress coil spring and turn handle
Lock
1/4 turn clockwise, then allow handle to
Position
raise into lock position.
5. Pressurizing and Spraying, continued
5C 5C 5D 5D 5E 5E
TO LOCK PUMP: Place TO UNLOCK PUMP: Turn TO RELEASE HANDLE:
pump prongs down into handle counterclockwise Push down to depress
slots in funnel, turn clamp until 3-prong clamp is coil spring and turn
clockwise to furthest loose. Then rotate clamp handle counterclock-
position under bottom slot, counterclockwise to wise 1/4 turn, then lift
then turn handle clockwise stop and lift out. handle.
until tightly locked and
sealed in place.
FOR HELP USING TRI-LOCK PUMP SEE VIDEO
https://chapinmfg.com/pages/industrial-videos
6A 6A
6. Lock Off
For safety lock-off feature (no-spraying), push
trigger forward and rotate locking mechanism
Lock
into lock-off positionas shown in fig. 6A.
7. To Use Special Valve to Pressurize Sprayer
SET COMPRESSOR REGULATOR AT 50 PSI.
To pressurize sprayer by using the special valve first remove plastic
cap from the tire valve stem. Pressurize the sprayer by using a
standard air chuck connected to an air compressor as you would
inflating a tire on a car. After pressurizing the sprayer replace
plastic cap on the tire valve to avoid getting dirt in the valve.
8. To Release Pressure
1) Do: To release pressure in the sprayer just pull the ring on the
relief valve until all pressure is released from the sprayer.
2) Do: Stay away from the sprayer until all air has escaped.
9. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with recommended solvent.
Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the
wand and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
5F 5F
Pump until you feel
resistance.
Trigger
7A 7A
8A 8A