Chapin 19099 Manual De Instrucciones

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious eye
or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized
sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or leave
solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection
when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or body
over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution from
striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not attempt
to modify this sprayer. Replace parts only with manufacturer's original parts. Never spray flammable, caustic,
acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemicals. Always
read and follow chemical manufacturer's instructions before use with this sprayer as some chemicals may
be hazardous when used with this sprayer.
Congratulations!
You have just purchased a quality Chapin product. Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store. Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin. Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda; llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin. Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin. Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-6092
Hose Black
Manguera para trabajos
pesados Negro
Tuyau pour service
intense Noir
6-8136
Valve Kit
Kit de la válvula
6-8301
Ensemble de soupape
.8 GPM Nozzle As-
sembly
Spanish
French
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
6-5373
Holster
Funda
Étui
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus)
1. Hose to Tank
1A
2. Extension wand and Nozzle Assembly
Sk-1154-1
Shut-off to wand to nozzle assembly
2A
Shut-off to nozzle assembly
2B
Metal Rod
To attach nozzle directly to shut-off, unthread brass extension nut and
metal rod. Assemble valve seat (included), nozzle adapter and nozzle to the
shut-off as shown in figure 2C. Note orientation of valve seat. It will leak if
assembled incorrectly.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank
for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and
could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and
replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes
and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of
these conditions are found, replace affected part with original manufacturer's part before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
6-4646
016761 (A) R1019
Attach the hose by screwing the swivel
nut clockwise and tightening to 37 in. lbs.
Refer to Pre-use check before using.
Metal Nozzle
Brass Extension
Nozzle
Rod Brass
Adapter
Extension Nut
The dripless shut-off comes assembled
as shown in figure 2A.
Metal Rod
2C
Valve Seat
Nozzle
Nozzle Adapter
5. Pressurizing and Spraying
5A 5A 5B 5B 5C 5C
Lock
Position
TO LOCK HANDLE: Push handle down to TO LOCK PUMP: Place pump prongs down into
depress coil spring and turn handle 1/4 turn clock- slots in funnel, turn clamp clockwise to furthest posi-
wise, then allow handle to raise into lock position. tion under bottom slot, then turn handle clockwise
until tightly locked and sealed in place.
5D 5D 5E 5E
TO RELEASE HANDLE:
TO UNLOCK PUMP:
Push down to depress coil
Turn handle counterclock-
spring and turn handle
wise until 3-prong clamp
counterclockwise 1/4 turn,
is loose. Then rotate clamp
then lift handle.
counterclockwise to stop
and lift out.
6. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle and move
locking mechanism away from you. To release, squeeze handle
and move the locking mechanism back towards you.
7. To Use Special Valve to Pressurize Sprayer
SET COMPRESSOR REGULATOR AT 50 PSI
To pressurize sprayer by using the special valve first remove plastic cap
from the tire valve stem. Pressurize the sprayer by using a standard air
chuck connected to an air compressor as you would inflating a tire on
a car. After pressurizing the sprayer replace plastic cap on the tire valve
to avoid getting dirt in the valve.
8. To Release Pressure
1) Do: To release pressure in the sprayer just pull the ring on the relief
valve until all pressure is released from the sprayer.
2) Do: Stay away from the sprayer until all air has escaped.
9. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with recommended solvent. Follow
Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle
are thoroughly rinsed after each use.
2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
5F 5F
Pump until you feel
resistance.
6A 6A
7A 7A
8A 8A