Important; Cleaning And Maintenance - Chicco SterilNaturalDigit Instrucciones De Uso

appliance is in use, the steriliser stops both the
disinfection cycle underway and the automatic
preset disinfection maintenance cycles. In this case,
the display will show 00, and the disinfection of
the products inserted in the appliance should be
considered incomplete and, therefore, insufficient.
h) A t the end of the disinfection cycles, or whenever the
appliance is not in use, disconnect the power cable
plug from the mains socket.
i) Remove the lid (diag. 11)
IMPORTANT: Wait a few minutes before removing the
lid at the end of the disinfecting cycle, as hot steam
could come out from the appliance.
j) U se the appropriate hygienic tongs supplied to remove
the feeding bottles and accessories from the steriliser.
(diag. 12)
Warning: Always clean your hands thoroughly before
touching the sterilised objects.
k) W hen the appliance is completely cold, remove any
water residues as shown in diagram 13. Dry the tank,
heating plate, lid and rack with a soft cloth.
WARNING
Always pour out the water as shown in diag. 13 to
avoid any infiltration in the appliance.
NOTE: Disinfected items will remain sterile inside
the steriliser with the lid on for about 5 hours.
NOTE: During the first disinfecting cycles, the appliance
could release a slight odour. This is not a sign of fault
or damage and should be considered normal.
Warning! If the water has run out or the disinfection
cycle is incomplete, the display will show the symbol
; the appliance will emit an acoustic signal (beep)
for 10 seconds and the display will show 00.

3) CLEANING AND MAINTENANCE

NOTE: These operations must always be carried out
only when the appliance has cooled down completely
and is disconnected from the mains socket.
a) Cleaning the Appliance before the First Use.
Before the first use, it is recommended to carry out a
disinfection cycle, without placing any feeding bottles
into the appliances, as described below:
1) R epeat the operations indicated in points a), b), c),
e), f) and g).
2) R epeat the operations indicated for the single
disinfection cycle (A).
NOTE: If it is necessary to switch off the appliance
during use, press the 0 button (d2) and disconnect
the power cable plug from the mains socket.
3) Repeat the operations indicated in points h), i), k).
WARNING
During the disinfection cycle, the hot steam
coming out from the small opening located on
All manuals and user guides at all-guides.com
the transparent lid could cause serious burns.
Always use the appliance with the utmost care and
attention.
b) How to Clean the Appliance.
1. A llow the steriliser cool down completely. Always
2. Disconnect the power cable from the steriliser,
3. R emove any residual water from the steriliser (diag.
4. Dry the steriliser with a soft, clean cloth.
5. Do not use abrasive or chemical products.
6. After cleaning, store the steriliser in a clean, dry
Note: To avoid the formation of unpleasant odours,
it is recommended not to replace the stopper (e1)
onto the water tank (e).
c) How to Clean the Tank:
Clean at least once a week, pouring a (100 ml) water
solution prepared with 50% white vinegar into the
tank. Tighten the stopper fully, shake the tank for
about 1 minute, unscrew the stopper and pour out all
the water.
Rinse the water tank and stopper thoroughly with cold
drinking water. Let dry without stopper.
Warning! Do not clean the water tank with detergents
or in a dishwasher.
Should the stopper have scale residues, it is necessary
to carry out a descaling cycle as follows: fill half a glass
with a solution made of equal parts of water and white
vinegar.Submerge the stopper in the solution and leave
overnight. At the end of the descaling cycle, rinse
thoroughly with cold drinking water.
4) DESCALING
The normal use of the steriliser can cause the formation
of scale residues on the heating plate. Excessive scale
residues on the heating plate may cause incorrect
operation and prevent the disinfection of the
objects inserted in the appliance, apart from causing
permanent damage to the appliance.Therefore, to
ensure the correct operation of the steriliser, avoid the
accumulation of scale residues.
Clean the heating plate (when it is cold), pouring 200
ml of white vinegar into the tank (at least once a week
or any time there are scale residues), and leave for at
least one night.
Then empty the tank, as indicated in diag. 13.
Remove the scale residues with a soft cloth and rinse
several times, pouring 300 ml of tap water into the
tank.
Pour out the water as indicated in diag. 13 and dry
thoroughly before use.
Warning: Never place the appliance under running
water.
Due to the different types of water (hardness) in
the different geographical areas, the formation
of scale deposits may be more abundant and
take place in a short time. To ensure the correct
operation of the appliance, it is recommended to
carry out descaling cycles more frequently.
The presence of scale residues on the heating plate
may cause a slight noise during use.
12
disconnect the plug from the mains before moving
the appliance, or carrying out any cleaning or
maintenance operations.
removing the connector from the socket located at
the back.
13) and tank.
place.