Multiplex TWISTER 21 4222 Instrucciones De Montaje página 7

Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you are
completely satisfied with the contents of your kit. However, we would ask you to check all the parts (referring to the Parts List) before
you start construction, as we cannot exchange components which you have already worked on. If you find any part is not
acceptable for any reason, please take the kit back to your model shop in the first instance, as he will be able to advise you. After
checking, he will send the component or the kit to our Quality Control department. We can only process guarantee claims if the
purchase receipt and a brief description of the fault are supplied.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents in
terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that we
cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings. Building and operating them safely
requires a certain level of technical competence and manual skill, together with discipline and a responsible attitude at the
flying field. Errors and carelessness in building and flying the model can result in serious personal injury and damage to
property. Since we, as manufacturers, have no control over the construction, maintenance and operation of our products, we
are obliged to take this opportunity to point out these hazards and to emphasise your personal responsibility.
Additional items required:
e.g. MULTIPLEX Micro IPD receiver
alternatively
or MULTIPLEX RX-7 SYNTH DS IPD receiver
MULTIPLEX Nano-S servo
Servo extension lead
Flight battery (minimum load capacity approx. 36 A):
MULTIPLEX flight pack, e.g. LiBatt 3/1-2500 mAh (load capacity approx. 45 A)
or MULTIPLEX flight pack, e.g. LiBatt 3/1-3200 mAh (load capacity approx. 64 A)
Adhesive: cyano-acrylate
Use medium and high-viscosity cyano-acrylate glue ("cyano" - not styrofoam cyano) for this model. Epoxy adhesives produce what
initially appears to be a sound joint, but the bond is only superficial, and the hard resin breaks away from the parts under load.
Hot-melt glue (from a glue gun) is an excellent alternative adhesive, especially for servo mounting.
Tools:
Scissors, balsa knife, combination pliers, long pointed-nose pliers, slot-head / cross-point screwdrivers (for the servo output arm
screws).
Specification:
Wingspan
Overall fuselage length
All-up weight, min.
Wing area
Wing loading (FAI) min.
RC functions
Important note
This model is not made of styrofoam™, and it is not possible to glue the material using white glue or epoxy. Please be sure
to use cyano-acrylate glue exclusively, preferably in conjunction with cyano activator ("kicker"). We recommend medium or
high-viscosity (thick) cyano. This is the procedure with Elapor®: spray cyano activator on one face of the joint; allow it to air-
dry for around two minutes until the surface appears to be "dry", then apply cyano adhesive to the other face. Join the parts,
and immediately position them accurately.
Please take care when handling cyano-acrylate adhesives. These materials harden in seconds, so don't get them on
your fingers or other parts of the body.
We strongly recommend the use of goggles to protect your eyes.
Keep the adhesive out of the reach of children!
35 MHz, A-band
40 MHz
35 MHz, A-band
2 x required for ailerons
1 x required for elevator
3 x 30 cm required for aileron
servos and speed controller
1 x 60 cm required for elevator servo
850 mm
1170 mm
750 - 880 g
26 dm²
29 g / dm²
Elevator, ailerons and throttle
Note: remove the picture pages from the centre of the building instructions.
# 21 4222
Order No. 5 5971
Order No. 5 5972
Order No. 5 5885
Order No. 6 5120
Order No. 8 5031
Order No. 8 5032
Order No. 15 7191
Order No. 15 7136
7