Publicidad
Idiomas disponibles
Idiomas disponibles
RELOAD LIGHT FX
1.- Power supply voltage selector.
2.- DIRECT PLAY: contact closures to initiate direct playback of a track. Each of these terminals 1-9
AUDIO
MIXER
corresponds to a track, 1 to 9 respectively, on the USB storage device or SD memory card. To start
SYSTEM
playback of a track, close and reopen the contact (with a push button), connecting and disconnecting
the track terminal with the COM terminal.
CONNECTION OK
3.- STEREO/MONO: selector which allows the audio output to be through two channels (STEREO) or
onesingle channel (MONO).
4.- AC socket to connect the mains supply cable provided.
5.- Grounding screw.
x2
6.- MP3 PLAYING: these contacts close when the MP3 playback is operating.
2s
7.- MASTER BALANCE: line level balanced master output, 2 x XLR connectors.
8.- MASTER UNBAL.: line level unbalanced master output, 2 x XLR connectors.
9.- REC OUT: recording output, line level, 2 x RCA connectors.
10.- AUX 3/4: line level aux inputs, 2 x RCA connectors.
11.- LINE/PHANTOM 48 V/MIC: input sensitivity switches and 48 V phantom power supply. These switches
have 3 positions:
LINE: in this position, line level audio sources can be connected to INPUT 1/2 : CD players, etc.
PHANTOM 48 V: in this position, electret condenser microphones that require 48 V phantom power
supply can be connected to INPUT 1/2.
MIC: in this position, low impedance 30-600 Ωdynamic microphones can be connected to INPUT 1/2.
12.- INPUT 1/2: mic./line inputs, combo connectors (XLR and 6.3 mm jack). Select the appropriate position
on the switch depending on the type of input being used.
13.- V.O. TIME: voice-over control. Allows the audio output attenuation level to be regulated when a
microphone signal is entered in INPUT 1. Turn the control in an anticlockwise direction to its minimum
and the rest of the inputs will automatically be attenuated when a signal is detected in INPUT 1. Turn it
in a clockwise direction to its maximum and the priority function will be set at its minimum level.
2 x AA
INSRUCTIONS FOR USE
If the programmer is switched on, the information display will look like this:
1
Configure the speaker
FE-1150T
Configure el altavoz
POWER
IMPEDANCE
100 V
70 V
15
7.5
670
10
5
1,000
Configurez le haut-parleur
5
2.5
2,000
3
1.5
3,300
1
0.5
10,000
Configure o altifalante
5 W
3 W
10 W
1 W
15 W
OFF
2
Connect the cables
Conecte los cables
Connectez les câbles
Ligue os cabos
On the first line, the date and present time will be shown.
On the second line, the day of the week and the time of the next event will be shown (if it is available).
On the third line, the current status of the MP3 player will be shown, which could be one of these options:
1.- MP3
04 ----- 00:01:52
Shows the audio track number that is being played and the playback time.
2.- MP3 STOP --- 36
Indicates that playback has stopped and the total number of audio tracks contained in the USB storage
device or the SD memory card.
L
3.- MP3 ERR
R
There is no USB storage device or SD card inserted.
4.- MP3 WAITING
The device is getting ready to read the USB storage device or the SD memory card. On the first line, the
date and present time will be shown.
SNOOZE
SOUND
Set on a free FM frequency
Seleccione una frecuencia FM libre
Sélectionnez une fréquence FM libre
Selecione uma frequência FM livre
Left (L)
Right (R)
Ground (G)
FUNCIONAMIENTO MP3
- 3 -
EN
MENU PRINCIPAL
Publicidad
