Publicidad
Idiomas disponibles
Idiomas disponibles
Using an Accessory Tool (Fig. L)
Your vacuum may come with some of the following tools.
-
Crevice tool.
-
2 in 1 brush
-
Pet hair tool.
•
The accessories
15
,
14
the extension tube
7
or to the vacuum inlet
in Fig. L.
•
Align the top of the accessories
vacuum inlet
5
or extension tube
it locks into position as shown in Fig. L.
MAINTENANCE
WARNING:
personal injury, turn unit off and remove battery
pack before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Cleaning and Emptying the Vacuum
WARNING:
never use the vac without its filter.
IMPORTanT: Maximum dust collection will only be obtained
with clean filters and an empty dust canister. If dust begins to
fall back out of the product after it is switched off, this indicates
that the dust canister is full and requires emptying.
nOTE: The filter is re-usable do not throw it away when the
product is emptied. We recommend that you replace the filters
,
every 6–9 months depending on frequency of use.
29
28
To Empty the Dust Canister and Remove the Pre-
filter (Fig. M–P)
1. Lift and remove the lift away dust canister
chassis
24
as shown in Fig. M.
2. While over top of a trash can, grip the recessed tabs
pre-filter
26
and pull upwards to remove the pre-filter with
cyclones and dust canister cap
3. Empty the contents of the dust canister
4. Tap the pre-filter
26
as necessary to remove any debris.
Inserting Pre-filter (Fig. O)
nOTE: The filter housing fits snuggly in the dust canister and
may be difficult to remove at first.
1. Install the pre-filter
26
the dust canister tab
27
shown in Fig. O.
2. Install the dust canister onto the chassis
firmly into position.
,
13
can be fitted either directly to
5
as shown
15
,
14
,
13
with the
7
and push into place so
To reduce the risk of serious
Projectile/Respiratory Hazard:
10
from the
9
.
10
.
into the dust canister
10
ensuring
aligns with the recessed tabs
24
, until it clicks
Removing filters (Fig. M—P)
1. Lift and remove the lift away dust canister
chassis
24
2. Unscrew the dust canister cap
the dust canister
3. Remove the foam filter
the plastic loop
Cleaning the filters
1. Once the filters and pre-filter are removed from the dust
canister
the pre-filter
2. Rinse out the dust canister
3. Wash the foam filter
soapy water.
4. Ensure the foam filter
dry before refitting the filters into the dust canister cap
5. Once the filters
them inside the dust canister cap
side in the upwards position.
nOTE: The black foam
into the dust canister cap from the underside.
6. With the filters
cap
9
clockwise onto the pre-filter
7. The pre-filter
dust canister
Pre-Filter section.
•
IMPORTanT:
Wash the filters regularly using warm, soapy water and
-
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
-
It is very important that the filters are completely dry
and correctly in position before use.
Removing and Cleaning the Rotary Brushes
(Fig. Q)
25
of the
WARNING:
moving parts, disconnect the floor head and extension tube
from the vacuum before cleaning or servicing.
1. To remove the rotary brush
the release latch
2. With the rotary brush
grab and lift the rotary brush
head
11
25
as
3. Wipe away any dust or debris on the rotary brush
4. Reinstall the rotary brush
aligning the keyed end of the rotary brush
located in the floor head
5. Align the squared end of the rotary brush
square slot on the floor head
6. Press firmly on the rotary brush
head
11
latch
32
as shown in Fig. M.
9
anticlockwise and lift off
10
.
29
and felt filter
30
.
10
shake off or lightly brush any loose dust from
26
and foam filter
29
10
with warm soapy water.
29
and felt filter
29
and felt filter
29
,
28
are clean and completely dry, place
29
side will be visible when looking
29
,
28
fitted, screw the dust canister
26
can now be inserted into the lift away
according to instructions in the Inserting
10
To reduce the risk of injury from
31
from the floor head
towards the rear of the floor head
32
released from the floor head
31
31
completely out of the floor
to clean.
31
into the floor head
11
.
11
.
31
. Ensure you hear an audible click as the release
snaps into its locked position.
EnGLIsH
10
from the
28
by pulling on
and felt filter
28
.
28
with warm
28
are completely
9
.
9
with the white felt
28
26
.
11
slide
.
11
,
11
31
.
11
by
31
with the gear
31
with the
to secure it into the floor
21
Publicidad
