Publicidad
Idiomas disponibles
Idiomas disponibles
g) Always keep proper footing and operate the pruner
only, when standing on fixed, secure and ground
level surface. Slippery or unstable surfaces such as
ladders may cause a loss of balance or control of the
pruner.
h) Follow instructions for oiling, chain tensioning
and changing accessories. Improperly tensioned or
lubricated chain may either break or increase the chance
for kickback.
i)
Keep handles dry, clean, and free from oil and
grease.
Greasy, oily handles are slippery causing loss
of control.
j)
Cut wood only. Don't use pole pruner for purposes
not intended. For example: do not use pole pruner
for cutting plastic, masonry or non-wood building
materials.
Use of the pole pruner for operations different
than intended could result in a hazardous situation.
k) Causes and operator prevention of kickback:
- Kickback may occur when the nose or tip of the guide
bar touches an object, or when the wood closes in and
pinches the saw chain in the cut.
- Tip contact in some cases may cause a sudden reverse
reaction, kicking the guide bar up and back towards the
operator.
- Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards the
operator.
- Either of these reactions may cause you to lose
control of the pole pruner which could result in serious
personal
injury. As a pole pruner user, you should
take several steps to keep your cutting jobs free from
accident or injury. Kickback is the result of tool misuse
and/or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as
given below:
l)
When cutting a branch be alert for kickback.
the branch is broached it can bend down and jam the
saw chain.
m) Only use replacement saw chains and bars
specified by the manufacturer. Incorrect replacement
of saw chains and bars may cause chain breakage and/
or kickback.
n) Always wait until the machine has come to a
complete stop, and remove the battery before
placing it down. The saw chain can jam or kickback and
lead to loss of control over the garden tool.
o) Switch off the pole pruner when changing the working
position.
Some regions have regulations that restrict the use of the
product. Check with your local authority for advice.
AFTER USE
Always switch off the tool and remove the battery
•
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
- after striking a foreign object
- whenever the tool starts vibrating abnormally
•
Store the tool indoors in a dry and locked-up place, out of
reach of children
- store the battery pack separately from the tool
BATTERIES
•
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
•
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
•
Do not use the battery when damaged; it should be
replaced
•
Do not disassemble the battery
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5 Do not expose tool to rain
6 Wear protective glasses and hearing protection
7 Store tool/charger/battery in locations where temperature
will not exceed 50°C
8 Do not dispose of electric tools and batteries together
with household waste material
9 Wear head protection
q Wear protective gloves
w Wear safety footwear
e Keep sufficient distance away from electrical power lines
USE
•
Assembly instructions
! remove battery from tool
! always use gloves when handling the chain
When
•
Assembling bar and chain r
- place the pole saw on any suitable flat surface –
remove cover plate D by turning locking knob C
counter-clockwise
- slide chain B in the slot around chain bar A
! ensure chain and bar have the same rotation
directions, and metal plate AH of bar should face
up
- fit the chain onto drive sprocket AG and chain bar A, so
that fastening bolt AE and the guide fins AF fit into the
keyway of chain bar A
! ensure chain is in correct running direction by
comparing with chain symbol AD
- check if all parts are seated properly and hold chain
and chain bar in a level position
- mount cover plate D as illustrated
- Lightly tighten the locking knob C by turning it
clockwise.Do not fully tighten the locking knob until
after you have adjusted the chain tension
•
Attaching the poles t
- Fit the front pole G together with one end of the
extension pole Q , tighten them together with the
threaded sleeve H by rotating it.Make sure that both
parts are properly fitted
- Repeat this process to attach the other end of the
extension pole Q to the rear pole V
•
Attaching the shoulder strap y
13
Publicidad
