Publicidad
Idiomas disponibles
Idiomas disponibles
Installation instructions
GB
GB
Dear customer,
You have purchased a high-quality and long-lasting product
from our line of goods. Please read these instructions care-
fully before assembling and observe the notes.
Therefore, keep the instructions in a safe place and pass
them on to possible subsequent owners.
Safety notes
• Only allow experts carry out the installation work.
• CAUTION DAMAGE BY WATER! Prior to installation please
turn the general water supply off.
• Ensure that all gaskets have the correct fit.
• These taps are not suitable for use on low pressure and
small electrical storage heaters.
• We recommend the installation of a filter into the appli-
ance or at least the use of angle valves with filter, in order
to avoid the inflow of foreign matter, which could damage
the upper parts of the valves.
• This tap is only intended for use in private households!
Only suitable for use in rooms with a temperature over 0 °C,
when there is danger of frost, sut off the water supply and
empty the tap.
• Incorrectly installed fittings can cause water damages!
• Please ensure that no caustic or corrosive products such as
detergents or household cleaning products make contact
with the connection hoses; this can lead to water damages.
• Despite careful production, sharp edges can occur. Please
exercise caution!
Technical data
• Flow pressure: Recommended as 1.5 to 6 bar; in case of
more than 6 bar connection pressure, we recommend that
a pressure reducer is installed.
Installation Instructions
• Only hand-screw the connecting pipes, do not use pliers
or a wrench!
• After installing the tap please unscrew the mixer nozzle,
flush the pipeline and the tap thoroughly for a longer time,
in order to flush out contaminations and residues.
• Do not twist or tension pipes! At first use check connec-
tions for leaktightness!
• Check all connections carefully after first-time use to make
sure that they are tight.
• We do not assume any warranty for incorrect installation -
in particular for subsequent damages!
Adjustment information for the runtime of the ECO-Stop
pillar tap
1. Lever the cap out of the handle with a pointed object.
2. Change the flow time via the adjustment screw with the
assistance of a screwdriver. Regulation for a longer flow
time: Adjust the adjustment screw in a clockwise direc-
tion. Regulation for a shorter flow time: Adjust the adjust-
ment screw in an anti-clockwise direction. Caution! Do
not completely unscrew the adjustment screw! Otherwise
water will leak out! If necessary, cut off the water supply
prior to the adjustment work.
3. Activate the handle by pressing in order to control the
flow time, re-adjust if necessary.
4. Replace the cap on the handle after setting the flow time.
Instructions for care
Sanitary taps require special care. Therefore, please observe
the following instructions:
• Chrome-plated surfaces are sensitive to lime-dissolving
agents, acidic cleaning agents and all kinds of abrasives.
• Never clean coloured surfaces with abrasive, corrosive, or
alcoholic agents.
• Only clean your taps with clear water and a soft cloth or a
shammy.
Do not forget to unscrew the mixing nozzle in regular inter-
vals and to remove possibly calcareous residues or foreign
matter. It is advisable to replace the mixing nozzle with a
new one in the case of extreme contamination.
Maintenance
• Please note that a valve top is a wearing part and that in
the case of very hard or soiled water the valve must be
replaced every 1 to 2 years, as required.
• Please check all joints and connections for leaks or visible
damages at regular intervals.
• In case of any leaks or visible damages to the fitting or con-
nection hoses, these should be immediately checked by a
specialist and replaced if necessary.
Decommissioning
• Cut off the water supply before dismantling the product.
• Pay attention to escaping residual water.
• Disassemble the product in the reverse order of the as-
sembly instructions.
Disposal
Your washbasin tap is delivered in a solid packaging, in or-
der to protect it against transport damages. The packaging
consists of recyclable materials. Dispose it in an environ-
mentally suitable manner.
Do not throw the product into the normal domestic waste at
the end of its service life, but ask your municipal administra-
tion about the possibility of an environmentally friendly
disposal.
The illustrations are to be considered as figurative
representations, deviations of the product are possible.
Subject to technical modifications.
WARRANTY CARD
The Franz Joseph Schütte GmbH, based in Wallenhorst,
shall take on a manufacturer's warranty for the product you
have procured in accordance with the warranty conditions
stated below. Your legal warranty claims from the purchase
contract with the seller and your legal rights shall not be
limited by this warranty.
Warranty conditions:
1. Scope of warranty
The Franz Joseph Schütte GmbH shall grant a warranty
for proper material qualities and material processing in
accordance with the intended purpose as well as professi-
onal assembly, tightness and function. The warranty shall
only apply for the country in which the product has been
procured.
8
Publicidad
