Fitting The Saw Blade - Triton TSA 001 Instrucciones De Uso Y De Seguridad

KICKBACK PREVENTION AND OPERATOR SAFETY:
Kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking precautions as follows:
a. Maintain a firm grip with both hands on the saw and
position your arms to resist kickback forces. Position
your body to either side of the blade but not in line
with the blade. Kickback could cause the saw to
jump backwards, however, if precautions are taken,
kickback forces can be controlled by the operator.
b. When the blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the workpiece until the blade comes to a
complete stop. Never attempt to remove the saw from
the work or pull the saw backward while the blade is
in motion. Investigate and take corrective action to
eliminate the cause of blade binding.
c. When restarting a saw within an incomplete cut, centre
the saw blade in the kerf and check that the saw teeth
are not engaged into the material (a binding saw blade
may 'propel upwards' or kickback from the workpiece
as the tool is restarted).
d. A large workpiece should be supported close to the
line of the cut, and at the edge of the panel, to prevent
sagging. This will minimise the risk of blade pinching
and kickback.
e. Do not use dull or damaged blades. Unsharpened or
improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
PREPARATION
Unpacking Your Tool
Carefully unpack and inspect your tool. Familiarise
yourself with all its features and functions.
Ensure that all parts of the tool are present and in good
condition. If any parts are missing or damaged, have such
parts replaced before attempting to use this tool.

FITTING THE SAW BLADE

• Only use 235mm blades, with a kerf between 2.2
and 3.5mm, designed for circular saws with a no
load speed rating of at least 4500min
high speed steel blades or abrasive discs to this tool.
GB
The use of incorrect accessories may invalidate the
warranty.
• Do not fit inferior blades. Regularly check the blade is
flat, sharp and free of cracks or defects.
Safety Instructions / Preparation
6
f. Blade depth and bevel adjusting locking levers must
be tight and secure before making a cut. If blade
adjustment shifts while cutting, it may cause binding
and kickback.
g. Use extra caution when making a 'plunge cut' into
existing walls or other blind areas. The protruding blade
may cut objects causing kickback.
h. Check the lower guard before each use and do not use
if it does not close freely, ensuring that the blade does
not touch any part of the guard or tool in all angles and
depths of cut. Never clamp or tie the lower guard in the
open position.
i. Check the operation of the lower guard spring. If the
guard and the spring are not operating correctly, they
must be serviced before use. The lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
j. The lower guard should be retracted manually only for
special cuts such as 'plunge cuts' and 'compound
cuts.' Raise the lower guard by the retracting handle
and as soon as the blade enters the material, the lower
guard must be released. For all other sawing, the lower
guard should operate automatically.
k. Ensure that the lower guard is covering the blade before
placing the saw down. An unprotected, coasting blade
will cause the saw to 'propel backwards', cutting
whatever is in its path. Be aware of the time it takes for
the blade to stop after the switch is released. Do not
use abrasive wheels, doing so will void the warranty.
. Do not fit
-1
1. Ensure the saw is disconnected from power.
2. Unscrew the handle half a turn to release the
spanner from the storage position, as shown. Press
the Spindle Lock (16), loosen and remove the blade
retaining bolt and outer flange washer from the arbor
shaft.
3. With the saw set at full cut depth, retract the guard
and fit the blade neatly onto the shaft against the inner
flange washer.