Publicidad
Idiomas disponibles
Idiomas disponibles
44. Have your tool repaired by a qualified
person – This electric tool complies with
the relevant safety rules. Repairs should
only be carried out by qualified persons,
otherwise this may result in considerable
danger to the user
WARKING:
When
identical replacement parts
WARKING: If the power cable is damaged it
must be replaced by the manufacturer or an
authorized service center
45. Power tool mains plugs must match
the mains socket – Never modify the
plug in any way. Do not use any adapter
plugs with earthed (grounded) power
tools. Unmodified plugs and matching
sockets will reduce risk of electric shock.
46. If operating a power tool outside use
a residual current device (RCD) – Use
of an RCD reduces the risk of electric
shock
NOTE: The term "residual current device
(RCD)" may be replaced by the term "ground
fault circuit interrupter (GFCI)" or "earth
leakage circuit breaker (ELCB)".
WARNING: When use in Australia or New
Zealand, it is recommended that this tool is
ALWAYS supplied via Residual Current
Device (RCD) with a rated residual current
of 30mA or less.
WARNING: Before connecting a tool to a
power source (mains switch power point
receptacle, outlet, etc) be sure that the
voltage supply is the same as that specified
on the nameplate of the tool. A power source
with a voltage greater than that specified for
the tool can result in serious injury to the
user, and damage to the tool. If in doubt, do
not plug in the tool. Using a power source
with a voltage less than the nameplate rating
is harmful to the motor.
Polarized Plugs (for North American only) To
reduce the risk of electric shock, this
equipment has a polarized plug (one blade
is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not
change the plug in any way.
Air Tool Safety
•
For
multiple
understand
the
before installing, operating, repairing,
maintaining, changing accessories on,
servicing
use
only
hazards,
read
and
safety
instructions
or working near this tool. Failure to do
so can result in serious bodily injury
•
Only qualified and trained operators
should install, adjust, or use this tool
•
Do not modify this tool. Modifications
can reduce the effectiveness of safety
measures and increase the risks to the
operator.
•
Do not discard the safety instructions;
give them to the operator
•
Do not use this tool if it has been
damaged
•
Tools shall be inspected periodically to
verify that the ratings and markings
required by this parts of ISO 11148 are
legibly marked on the tool. The
employer
should
manufacturer to obtain replacement
marking labels when necessary.
WARNING: This appliance is not intended
for use by persons (including children) with
reduced, physical or mental capabilities or
lack of experience or knowledge unless
they have been given supervisor or
instruction concerning use of the appliance
by a person responsible for their safety.
Children must be supervised to ensure that
they do not play with the appliance.
Projectile Hazards
•
Be aware that failure of the workpiece
or accessories, or even of the inserted
too itself, can generate high-velocity
projectiles
•
Always
wear
impact-resistant
protection during operation of this tool.
The grade of protection required should
be assessed for each use
•
For overhead work, wear a safety
helmet
•
The risks to others should also be
assessed at this time
•
Ensure that the workpiece is securely
fixed
Entanglement Hazards
•
Choking, scalping and/or lacerations
can occur if loose clothing, personal
jewelry, neck wear, hair or gloves are
not kept away from the tool and its
accessories.
Operating Hazards
•
Use of the tool can expose the
operator´s hands to hazards, including
cuts, abrasions and heat
•
Wear suitable gloves to protect hands
contact
the
eye
Publicidad
