Publicidad
Idiomas disponibles
Idiomas disponibles
18 | English
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A separate protective guard for cutting must be used when
cutting with bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
Technical data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Restart protection
Weight according to EPTA-Procedure 01:2014
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 91
dB(A); sound power level 102 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
1 609 92A 6PD | (21.06.2021)
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
(3) Lever
(4) On/off switch
(5) Auxiliary handle (insulated gripping surface)
(6) Protective guard for grinding
(7) X-LOCK grinding disc/flap disc
(8) Protective guard for cutting
a)
(9) X-LOCK cutting disc
(10) X-LOCK backing pad for fibre discs
a)
(11) X-LOCK fibre disc
(12) X-LOCK clip for fibre discs
a)
(13) Hand guard
(14) X-LOCK cup brush/disc brush
(15) X-LOCK holder
(16) Handle (insulated gripping surface)
(17) Extraction guard for cutting with a guide block
a)
(18) Diamond cutting disc
(19) X-LOCK diamond core cutter
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GWX 750-115
3 601 GC9 2..
W
750
W
380
-1
min
11,000
mm
115
kg
1.8
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2
2
a
= 9.5 m/s
, K = 1.5 m/s
,
h
Disc sanding:
2
2
a
= 4.5 m/s
, K = 1.5 m/s
.
h
a)
a)
a)
a)
a)
a)
a)
GWX 750-125
3 601 GC9 2..
750
380
11,000
125
●
●
1.8
/ II
/ II
Bosch Power Tools
Publicidad
