Multiplex AcroMaster Pro Instrucciones De Montaje página 9

Assembly instructions
Before assembly
Use the list of components on page 8 and Fig. 01 + 02 to check the
completeness of the components supplied.
We recommend using a soft, clean and lat surface to ensure the model is
not damaged during assembly. Always use, unless otherwise speciically
stated Zacki ELAPOR CA instant adhesive to glue the model.
®
1. Assembling the elevator
7
Slide the elevator into the rear of the fuselage
it and that it is at a right angle to the fuselage. Pull it back out again
from the rear and sand the contact surfaces slightly to ensure the
adhesive adheres better later on. Make sure it its correctly again. If you
are satisied, apply Zacki ELAPOR
elevator Fig. 03 . If necessary, use a paper towel to remove any excess
adhesive. Ensure that it is at a right angle to the fuselage and that the
lengths A and B are identical Fig. 04 + 05 . A little activator spray speeds
up the process.
Use the remote control to set the elevator servo to the neutral position.
Make sure the elevator lap is also in the neutral position and screw the
pushrod to the elevator horn.
2. Assembling the rudder
Proceed with the rudder in the same way as with the elevator. This means,
initially check correct it, then sand accordingly, apply adhesive, and align
Fig. 06 . Ensure that it is also at a right angle to the fuselage Fig. 07 .
Use the remote control to set the rudder servo to the neutral position.
Make sure the rudder lap is also in the neutral position and screw the
pushrod to the rudder horn.
3. Assembling the undercarriage
Screw the undercarriage
screws Fig. 08 .
4. Assembling the wings to the fuselage
The long CFRP tube is the rear main spar and the short CFRP tube
is the front auxiliary spar. Slide the spars into one wing and insert it
into the fuselage. Now slide on the other wing and make sure that both
servo cables are routed upward into the fuselage Fig. 09 . To secure the
wings, insert the wing lock from above into the slots of the two wings
Fig. 10 .
5. Assembling the propeller
Push the propeller coupling
Balance the propeller , e.g. using the propeller balancer # 33 2355
or similar. Slide on the propeller and then the holder for the spinner
Slide on the washer and screw on the nut Fig. 11 . Tighten the nut irmly.
Finally, position the spinner
www.modellmarkt24.ch; www.modellmarkt24.ch;
4
and check the
to the fuselage and then insert the
®
to the fuselage using the self-tapping
as far as possible onto the motor shaft.
on the holder.
6. Assembling the receiver
Insert the servo plugs into the receiver and use the hook and loop tape
and to ix it to the area provided for this purpose in the fuselage
Fig. 12 . The servo plugs are labeled as follows:
1 LH aileron; 2 Elevator; 3 Rudder; 4 Motor; 5 RH aileron
7. Assembling the battery
Use the hook and loop tape
board Fig. 15 and tighten the hook and loop strap
Fig. 13 . Insert the battery into the battery rail Fig. 14 and also ix it into
position using the hook and loop tape
loop strap . To do so, thread the hook and loop strap through the slot
in the battery board and in the Elapor and tighten irmly Fig. 15 .
8. Preflight check and center of gravity
Always check the model before lying it for the irst time. Check the
following points before the initial light:
• Rudder horns tight
• Servo screws tight (cross-head screws)
• Linkage rod tight (hex grub screws)
• Make sure the spinner is running true by rotating the propeller by hand
Position and secure the battery (3S 2600 mAh 40C) and the receiver in
the model using the hook and loop tape and strap so that the center of
gravity at the fuselage is 110 mm behind the leading edge Fig. 16 .
9. Rudder deflections
Normal settings
Aileron distances
40% Expo
Aileron +/- 30 mm
Elevator +/- 40 mm
Rudder +/- 55 mm
3D settings
Aileron distances
60% Expo
Aileron +/- 50 mm
Elevator +/- 60 mm
Rudder +/- 85 mm
10. Initial flight
Carry out a range test and make sure all the rudders are running in the
correct direction and are in the neutral position. Start the model from
⓾ the ground and familiarize yourself with the light characteristics at high
.
altitude.
www.modellmarkt24.de www.modellmarkt24.de
and to ix the battery to the battery
around both
and , as well as a hook and
Mounting points
Innermost servo Outside rudder horn
Innermost servo Outside rudder horn
Innermost servo Outside rudder horn
Mounting points
Servo 2nd hole from Outside rudder horn
outside
Outermost servo Center rudder horn
Outermost servo Center rudder horn
EN
9