Bosch UniversalDrill 18V Manual Original página 232

Technical data
Cordless Impact Wrench
Article number
Rated voltage
A)
No-load speed
A)
Impact rate
Maximum torque, hard
screwdriving application ac-
A)
cording to ISO 5393
Machine screw diameter
Max. screw diameter
Tool holder
Weight according to
B)
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Recommended rechargeable
batteries
D)
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery PBA 18V
1.5Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
D) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/vibration information
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 95 dB(A); sound power level
106 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
2 2
a = 11 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
Bosch Power Tools
increase the vibration and noise emissions over the total
working period.
AdvancedImpact
To estimate vibration and noise emissions accurately, the
Drive 18
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
3 601 J80 3..
This may significantly reduce vibration and noise emissions
V= 18
over the total working period.
-1
min 0–2600
Implement additional safety measures to protect the oper-
-1
min 0–3200
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
Nm 130
and organising workflows correctly.
Assembly
mm M4–M14
mm 8
u
¼" internal
hexagon
kg 1.2–1.5
°C 0 to +35
Battery Charging
Note: The battery is supplied partially charged. To ensure
°C –20 to +50
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
PBA 18V...W-.
reducing its service life. Interrupting the charging process
does not damage the battery.
AL 18...
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
– To remove the battery (4), press the release button (3)
Changing the tool (see figure A)
u
Inserting the application tool
– Pull the locking sleeve (2) forward, guide the application
– Use only screwdriver bits with ball catch (8) (DIN 3126-
Removing the application tool
– Pull the locking sleeve (2) forward and remove the applic-
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
and pull the battery back and out of the power tool. Do
not use force to do this.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
tool (1) into the tool holder up to the stop and release the
locking sleeve (2) to lock the application tool.
E6.3). Other screwdriver bits (9) can be inserted using a
universal bit holder with ball catch (10).
ation tool.
1 609 92A 7UC | (25.05.2022)
English | 13