Publicidad
Idiomas disponibles
Idiomas disponibles
devices (see Table 1.1 Technical specifications). In cases of too much draught, when the duct exceeds 7 meters in length, or the
measurement exceeds 20 Pa, the draft must be adjusted. To do this, use the second part of the baffle plate, to install it follow the
steps: "D.7" to "D.11" or adjust the air intake through the grille and / or the flow of the registers: in this case, go to Section 4.4.1
Primary Registrer and 4.4.2 Secondary Registrer.
2.3 Type of appliance "Vermiculite" home plate at the bottom, sides and baffle plate, fire grate, ash pan and ventilation set
incorporated. The fireplace comes ready to install. Provision should be made from inside an output for the electric cable. All the inner
can be removed if desired, for easier transportation and installation.
2.4 Security insulating and safety distances. You must be respected the values described in 1.1 Technical characteristics.
Anything fragile or flammable (textile, electronics, wood, paper wall, glass, chalk...) should be separated of the appliance and
respected the safety distances described in 1.1 Technical characteristics.
We must take special care in those fireplaces with wooden shelves or similar: we must prevent and avoid the possibility of hot air
that expels the device falls directly on the wood, in these cases, flammable items should be properly insulated.
2.5 Air supply. Air should be provided to the room where the appliance is installed. This is especially relevant when outside air is not
used and also when the door is opened for reloading with logs. This entry cannot be less than 225 cm
operation with other ventilation devices and / or heating such as exhaust fans, heat pumps, etc. In these cases, the extraction must
be compensated with a corresponding air entry from outside.
2.6 Changes to the device. Any intended change to the equipment must be authorized in writing by Manufacturas Rocal, S.A. We
also recommend using only original spare parts or parts recommended by Manufacturas Rocal, S.
3. INSTALLATION
3.1 Installation process. To proceed with the installation, follow the steps outlined in Section III of the ANNEXED document.
WARNING: The second part of the deflector shield must be adjusted in case there is an excessive draught, follow the steps 'D.7' to
'D.11'. To adjust the door lock, follow the steps 'D.12' and 'D.13'.
. USE AND OPERATION
4
4.1 Fuels authorized by the manufacturer. The appliance should not be used as an incinerator and the use of fuels other than
those authorized by the manufacturer are prohibited, including lighting liquids or gels. Only natural wood logs are authorized as fuel
and it is not advisable to use resinous woods.
CAUTION:
- The maximum load allowed by the manufacturer, the measurements of the logs and the height of the
reload must be respected.
- Do not touch or manipulate any part of the appliance when in operation without a protection glove.
- Check that there are no materials left inside the device, paying special attention to the paint spray.
4.2 Efficient combustion. During combustion the flame should not be extinguished, in this case the unburned gases produce
corrosion, dirt in the duct and polluting gases. The air controls must be opened, particularly the secondary one.
4.3 Pilot fire lighting. For a reasonable period of time, approximately 24 hours, it must not exceed 50% of the Maximum load allowed
by the manufacturer. Before lighting the fire, ensure that nothing delivered with the equipment has stayed inside (such as gloves,
spray paint ...)
4.4 Combustion control. The appliance has mechanisms to regulate combustion.
4.4.1 Primary register. The primary register is used to control the air entering the combustion chamber through the base of the fire,
through the fire grate. The primary register should be used mainly for lighting and, if necessary, to aid combustion. To locate the
register control handle and to know how to use it see picture "D.2" on page 8 of the ANNEXED document. If there is too much draught,
adjust the air through the grill, image "D.26" and / or adjust the path of the primary register following the steps: "D.23" to "D.25".
4.4.2 Secondary register. The secondary register is used to control the air entering the combustion chamber from the top. The
secondary register is used as combustion intensity adjustment. To locate the register control handle and to know how to use it see
picture "D.3" on page 8 of the ANNEXED document. If there is too much draught you can adjust the path of the secondary register
following the steps: "D.23" to "D.25".
4.4.3 Tertiary or safety air. The appliance has a fixed air supply through the rear vermiculite, under the deflector, to prevent possible
deflagerations and improve combustion.
4.5 Fire lighting. To light the fire, use suitable materials for this purpose, such as heat pads, paper, dry and thin branches. DO NOT
USE GASOLINE, SOLVENTS OR ALCOHOL. To see the correct position see picture "D.4" on page 8 of the ANNEXED document,
then light the fire using a suitable material. Once the fire is lit keep the door and the registers open for a reasonable time to prevent
condensation on the door. When the apparatus is hot enough close the door, adjust the primary register to avoid excessive combustion
and control the intensity of fire by the child record.
IMPORTANT:
-The interior vermiculite parts SHOULD NOT RECEIVE IMPACTS when refueling is performed.
If any of these parts crack, but is properly set in its place, THE PROPER OPERATION OF THE
APPLIANCE SHALL NOT BE ALTERED AND THERE IS NO POTENTIAL RISK. The equipment can be
used normally. These cracks do not entail any manufacturing defect so they do not fall under
guarantee.
4.6 Loading and reloading of fuel. Do not exceed the maximum allowed load or reload. (See Table of Technical specifications).
2
. Also note the simultaneous
11
Publicidad
