Kreg ACS-SAW Manual Del Propietário página 4

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

filter out microscopic particles.

equipment, such as those dust masks that are specially designed to

• Avoid prolonged contact with dust from power sanding,

filter out microscopic particles.

dust to get into your mouth, eyes, or

sawing, grinding, drilling, and other construction activities.

• Avoid prolonged contact with dust from power sanding,

Terms and Definitions

Wear protective clothing and wash exposed areas with

sawing, grinding, drilling, and other construction activities.

The label on the saw may include the symbols below.

soap and water. Allowing dust to get into your mouth, eyes, or

Wear protective clothing and wash exposed areas with

or respirator should be worn by all

The symbols and their definitions are as follows:

lay on the skin may promote absorption of harmful chemicals.

soap and water. Allowing dust to get into your mouth, eyes, or

WARNING: A dust mask or respirator should be worn by all

lay on the skin may promote absorption of harmful chemicals.

persons entering the work area. The filter should be replaced daily or

WARNING: A dust mask or respirator should be worn by all

safety alert symbol

whenever the wearer has difficulty breathing. See your local hardware

persons entering the work area. The filter should be replaced daily or

volts

store for the proper NIOSH/OSHA approved dust mask.

whenever the wearer has difficulty breathing. See your local hardware

• The label on your tool may include the following symbols. The

store for the proper NIOSH/OSHA approved dust mask.

hertz

are as follows:

symbols and their definitions are as follows:

• The label on your tool may include the following symbols. The

amperes

A .......amperes

V ......... volts

symbols and their definitions are as follows:

A .......amperes

watts

W ......watts

V ......... volts

Hz ....... hertz

W ......watts

direct current

W ......watts

Hz ....... hertz

min ..... minutes

.....alternating current

alternating current

min ..... minutes

... direct current

.....alternating current

.....alternating or direct current

alternating or direct current

.....alternating or direct current

... direct current

....... Class I Construction

.....alternating or direct current

n o ......no load speed

Class I Construction (grounded)

n o ......no load speed

....... Class I Construction

...........

(grounded)

n o ......no load speed

Class II Tool (double insulated)

...........

(grounded)

....... Class II Construction

......earthing terminal

....... Class II Construction

earthing terminal

...........

(double insulated)

......earthing terminal

.....safety alert symbol

...........

(double insulated)

minutes

.../min per minute

min

A .......amperes

.....safety alert symbol

.../min per minute

BPM ..beats per minute

revolutions or reciprocations per minute

/min

BPM ..beats per minute

W ......watts

BPM ..beats per minute

beats per minute

BPM

.....alternating current

RPM ..revolutions per minute

revolutions per minute

RPM

.....alternating or direct current

n o ......no load speed

no load speed

......earthing terminal

Read the instructions

.....safety alert symbol

BPM ..beats per minute

Wear eye and ear protection

RPM ..revolutions per minute

Keep hands & body away from and to the side

of the blade. Contact with blade will result in

serious injury.

Blade change mode

Cut mode

GENERAL SAFETY GUIDELINES

Kreg

120V ~ 60 Hz 12A no = 2,000-6,000/min

Guidelines for extension cord use

Extension cords are only to be used for temporary purposes. They

do not replace the need for installation of outlets and proper wiring

where necessary.

In your work area:

1. Extension cords with an equipment grounding conductor

2. Extension cords must be protected from damage, and not

run through doorways or windows where the doors or

windows can close, causing damage to the cord.

3. Extension cords must be a minimum of 16 AWG and be

rated for the equipment in use.

4. Extension cords must be periodically inspected to ensure that

A .......amperes

5. Extension cords should not be run through water or allowed to

A .......amperes

W ......watts

.....alternating current

TABLE 1

Nameplate

.....alternating current

.....alternating or direct current

n o ......no load speed

.....alternating or direct current

n o ......no load speed

......earthing terminal

.....safety alert symbol

BPM ..beats per minute

NR – Not Recommended

BPM ..beats per minute

RPM ..revolutions per minute

ACS-SAW

and other chemicals, which are known to the State of California to cause cancer and

reproductive harm. For more information go to www.P65Warnings.ca.gov.

you to wood dust, a substance known to the State of California to cause cancer. Avoid

inhaling wood dust or use a dust mask or other safeguards for personal protection.

For more information go to www.P65Warnings.ca.gov/wood.

ACS430

Carbon 1333-86-4, which are known to the State of California to cause cancer.

For more information go to www.P65Warnings.ca.gov.

KPS6512 plunge saw motor specifications

must be used at all times.

the insulation and conductivity of the wires are not compromised.

have connections that may be exposed to accumulated water.

Amperes

25'

50'

@120 V

Recommended Wire Gauge

0 -5

5.1 - 8

8.1 -12

12.1 - 16

WARNING:

This product can expose you to chemicals including Acrylonitrile

WARNING:

Drilling, sawing, sanding or machining wood products can expose

WARNING:

This product can expose you to chemicals including

Extension Cord Length

75'

100'

150'

200'

Tabla de Contenido

Tabla de contenido

Productos relacionados para Kreg ACS-SAW

Este manual también es adecuado para:

Acs430 Acs445 Acs735 Acs705

Kreg ACS-SAW Manual Del Propietário página 4

Idiomas disponibles

Manuales relacionados para Kreg ACS-SAW

Productos relacionados para Kreg ACS-SAW

Este manual también es adecuado para:

Tabla de contenido