Publicidad
The sweeping track should have an even
rectangular shape which is between 30 and
40 mm wide.
Setting range
Minimum sweeping track
Maximum sweeping track
New roller brush
Adjust sweeping track:
Adjust the left and right adjustment le-
vers and engage into the same boring.
– Engage adjustment lever into the lower
boring (+): Sweeping track becomes
bigger
– Engage the adjustment lever into the
upper boring (-): Sweeping track be-
comes smaller
Check sweeping mirror.
Replacing side brush
Replacement is due if a visible deterioration
in sweeping performance caused by bristle
wear is evident.
Note
– The appliance may only be tilted back-
wards if the fuel tank is empty.
– Close the fuel tap, remove the waste
container and move the pushing handle
to the front prior to tilting the appliance.
Do not rest the appliance on the push-
ing handle.
Unscrew 3 screws from the underside of
the side brush.
Remove the wiper blade.
Clip new side brushes on to driver and
screw on.
Adjust side-brush lowering
Adjustment is necessary if a visible deterio-
ration in sweeping performance caused by
side-brush is evident.
Release the wing nut.
Adjust the adjustment screw.
Tighten the wing nut.
Adjust the raising of the bulk waste flap
– Adjustment is necessary if the bulk
waste flap cannot be raised wide
enough.
(-) 1...10 (+)
– The Bowden cable needs to be re-
leased a little if the sweeper results be-
1
come poorer, for e.g. due to the wearing
10
of the front lip.
1...3
Loosen counter-nut.
Adjust the adjustment screw.
Tighten the counter-nut.
Adjusting and replacing sealing strips
Note
– The appliance may only be tilted back-
wards if the fuel tank is empty.
– Close the fuel tap, remove the waste
container and move the pushing handle
to the front prior to tilting the appliance.
Do not rest the appliance on the push-
ing handle.
Front sealing strip
Loosen the fastening screws of the
sealing strip.
Adjust or replace sealing strip.
Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 0-10 mm.
Adjust sealing strip.
Tighten the fastening of the sealing
strip.
Rear sealing strip
Remove the waste container.
Loosen the fastening screws of the
sealing strip.
Adjust or replace sealing strip.
Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 0-10 mm.
Tighten the fastening of the sealing
strip.
Side sealing strips
Loosen the fastening screws of the
sealing strip.
Adjust or replace sealing strip.
To set the floor clearance, insert a sheet
with a thickness of max. 2 mm under the
sealing strip.
Adjust sealing strip.
Tighten the fastening of the sealing
strip.
Replacing dust filter
Danger
Empty waste container before replacing
dust filter. Wear a dust mask when working
around the dust filter. Observe safety regu-
lations on the handling of fine particulate
material.
Lock parking brake.
Shake off dust filter.
Open the locking screw of the dust filter
cover in an anticlockwise direction.
Lift the dust filter cover.
Replace dust filter Make sure the dust
filter is inserted correctly (see figure).
Screw in the locking screw all the way.
Warning
If the locking screw is not tightened all the
way, there may be damages.
Note
Make sure when installing the new filter that
the fins are not damaged.
Accessories
Hard side-brushes
6.905-625.0
For removing stubborn dirt in the external
area; resistant to moisture.
Roller-brush, soft
6.906-886.0
With natural bristles especially for fine
dust sweeping on smooth indoor floors.
Not resistant to wetness; not for abrasive
surfaces.
Roller-brush, hard
6.906-885.0
For removing stubborn dirt in the external
area; resistant to moisture.
Roller brush, anti-
6.906-950.0
static
19
English
Publicidad
