LUND 68172 Manual De Instrucciones página 10

GB
PRODUCT CHARACTERISTICS
Electric kettle is designed for water heating and boiling. Thanks to its high power it is possible to boil water quickly. Detachable
base ensures convenient and safe usage of the kettle. The product is intended only for home use. Correct, reliable and safe
operation of the product depends on proper operation, therefore:
Before starting product operation, please read this manual and keep it.
The supplier does not assume any liability for damages resulting from failure to follow safety regulations and recommendations
specifi ed in this manual.
SAFETY INSTRUCTIONS
Note! Product may heat up to high temperature during operation, be cautious when handling it. The product should be held using
only the handle.
Recommendations for the product transportation and installation
The product can be placed only on a hard, fl at, level and non-fl ammable surface resistant to high temperatures. Substrate should
withstand the weight of appliance itself together with water poured into it.
Provide at least 10 cm space around product's side walls, do not place any materials not resistant to high temperature above the
product. This will allow for proper product ventilation. Do not place the product near edges e.g. of a table. Do not put anything on
the product. It impairs air circulation and may be a cause of product damage, as well as fi re.
Do not place the product near fl ammable materials, e.g. curtains or drapes.
Do not place any electrical appliances over the product. Steam is released during operation of the product, which may cause a
short circuit of electrical installation resulting in electric shock.
It is forbidden to drill any hole in the product, nor any other product modifi cation not described herein.
Carry the product with hot water by grasping the handle and lifting up from the base. Do not carry the hot product along with the
base. Do not displace the product by pulling the cable cord.
Temperature at the place of product installation and use must stay within the range +10 C ÷ +38 C and the relative humidity must
O O
be less than 90%, without steam condensation.
Recommendations for connecting the product to power supply
Before connecting the product to power supply, make sure that the voltage, frequency, and capacity of mains supply correspond
to values shown on the product rating plate. Plug must fi t into the socket. It is forbidden to modify the plug or socket in order to
fi t each other.
Product must be connected directly to a single power outlet. It is forbidden to use extension cords, socket-outlet adapters and
double power outlets. Power supply circuit must be fi tted with a protective conductor and at least 16 A protection circuit.
Avoid any contact of power cord with sharp edges and hot objects and surfaces. When operating the product, the power cord
must always be fully unwound and its position may not interfere with the operation of product. Laying of power cable cannot result
in tripping hazard. Power outlet should be located in such a place to allow always the possibility of quick disconnecting the plug
of power cord supplying the product. When disconnecting the plug of power cord always pull the plug housing, never the cable.
If the power cord or plug is damaged, disconnect it immediately from the mains and contact an authorized manufacturer's service
centre for replacement. Do not use the product with a damaged power cord or plug. Power cord or plug cannot be repaired, in
case of damage to these components, replace them with new ones without defects.
Recommendations for using the product
Note! The product is designed only for heating and boiling water. It is forbidden to use the product for heating and boiling liquids
or substances other than water.
Product must be used together with the base supplied. When using the product, power cord should be completely unwound.
Rolled-up cable under the base may overheat and pose a threat of fi re and electric shock.
Make sure that the fl oor next to the place where the product is used is not slippery. This will prevent the risk of slipping, which
may cause severe injuries.
The product may be plugged in only during operation. After it is completed, unplug the product, by removing the plug from the
mains socket. Do not leave the connected product unattended.
Fill the product with water by pouring it into the kettle. Never immerse the kettle in water or other liquid. If water is splashed while
fi lling the kettle on the outside surface of kettle or on the base, it should be thoroughly dried before connecting the kettle to power
supply.
Avoid fi lling the hot kettle with cold water, this may cause the glass kettle housing to crack due to excessive temperature diff erence.
Do not start the product without water. Water level must always remain between the minimum and maximum level markers. Lower
water level can cause the damage to product or cause the product fails to start. Higher water level can make it splattering during
cooking, which can cause serious burns.
O R I G I N A L I N S T R U C T I O N S
10