LUND 68172 Manual De Instrucciones página 12

GB
Note! Pushing the switch manually completes the process of heating water at any time.
Note! If water temperature is changed to lower value in the course of heating or the kettle is raised from the base, the kettle will
automatically fi nish the water heating process.
Note! If water temperature set is lower than the temperature of water in the kettle, it will not be possible to switch on the kettle. The
kettle does not have the water cooling function.
Model 68174
Lift the lid by pressing the button.
Fill the kettle with water so that its level remains between the minimum and maximum level markers. Cover the lid of the kettle.
Connect the power cord to the mains socket. The display in the base will show "E1" message.
Place the kettle on the base so that the kettle adheres to the base with its entire perimeter. Current water temperature will be
visible on the display.
Set up water temperature using "+" and "-" buttons. Pre-set water temperature is 100 C. If no other temperature is set before the
o
kettle is switched on, the kettle will boil water.
Switch-on the kettle by pushing the switch.
Kettle's light indicator will be visible throughout the entire cooking time, and the display will show water temperature.
After the water boils, the kettle will automatically switch off . Light indicator will go out and also acoustic signal will be emitted.
Raise the kettle from the base by grasping the handle only.
It is not necessary to open the lid for pouring water.
Unplug the power cord from the mains socket.
After the use, leave the product to cool. down.
Note! Pushing the switch manually completes the process of heating water at any time.
Note! If water temperature is changed to lower value in the course of heating or the kettle is raised from the base, the kettle will
automatically fi nish the water heating process.
Note! If water temperature set is lower than the temperature of water in the kettle, it will not be possible to switch on the kettle. The
kettle does not have the water cooling function.
Note! After approx. 10 minutes of idleness, the kettle will automatically switch off . The display will be extinguished.
The display in 68174 model may display the following messages:
E1 - no contact of the kettle with the base,
E2 - short circuit detected,
E3 - dry switching - no water in the kettle.
Due to thermal inertia of temperature sensor, a slight disparity between actual water temperature and display indications is possi-
ble. Sensor inaccuracy is given in the technical data table.
Water temperature sustaining function
Setting the water temperature and pressing the button marked with a cup will activate the water temperature sustaining function.
The function allows heating the water and then maintaining the temperature set.
Note! Lifting the kettle up from the base switches off the water temperature sustaining function.
Note! Water temperature sustaining function can be switched on for a maximum of 8 hours. After this time, the kettle will switch
off automatically.
MAINTENANCE, TRANSPORT, STORAGE
Kettle maintenance
Since the product is designed for preparation of water intended for comestible purpose, one should take care of its cleanliness
and it should be regularly maintained.
NOTE! All maintenance operations to be carried out with the power supply off . To this end, remove the plug of the power cord
from the mains socket.
NOTE! The product must not be immersed in water or in any other liquid. The product must not be washed under running water,
in dishwashers or under water jets.
NOTE! Before any maintenance operations, allow the product components to cool down completely. Do not speed up the cooling
process by fi lling the kettle with cold water.
For cleaning, use a mild dishwashing detergent. Residues of solution to be removed using a cloth soaked with water (base and
outer part of the kettle) or fi lling the kettle with water several times (inside of the kettle). Then wipe the product to dry or leave to
be dried off .
The kettle has been fi tted with a screen fi lter located at the water outlet. If the fi lter can be dismounted, it can be cleaned using a
water jet after dismounting it from the kettle. The fi lter that cannot be dismounted should be cleaned with a damp cloth or sponge.
Do not apply too much pressure that could damage the fi lter.
O R I G I N A L I N S T R U C T I O N S
12