PERFECTPRO RH4-18V Instrucciones De Uso página 6

Ocultar thumbs

página de 90

/ 90
Marcadores

Idiomas disponibles

Note:

Before selecting the DAB radio mode and performing

a scan, make sure the DAB / FM antenna has been

positioned upright.

The DAB radio menu

You can open the DAB radio menu by pressing and

holding the Info / Menu button while the radio is in the

DAB radio mode.

Rotate the Tuning knob to select one of the options and

then press the Tuning knob to confirm your choice.

The radio's default and recommended settings are

indicated using an asterisk.

The DAB radio menu offers the following options:

● [Station list]: Select this option display all DAB radio

stations that were found and tune into one of the

stations.

● [Full Scan]: Select this option to perform a full scan

and store all DAB radio stations that were found in the

station list. Alternatively press Auto tune button to scan

for new stations.

● [Manual Tune]: Select this option to manually tune into

a DAB channel / frequency.

● [Station order]: Select this option and subsequently

select [Alphanumeric] to sort the station list

alphanumerically or select [Ensemble] to sort the

station list by DAB multiplex or select [Valid] to show

only those stations for which a signal can be found.

● [DRC]: Dynamic Range Control (also known as DRC)

can make quieter sounds easier to hear when your

radio is used in a noisy environment by reducing the

dynamic range of the audio signal.

After selecting this option, select the required DRC

setting:

[DRC off]: DRC is switched off. Broadcast DRC will be

ignored. This is the default setting.

[DRC low]: DRC level is set to 1 / 2 that sent by

broadcaster.

[DRC high]: DRC is set as sent by broadcaster.

NOTE: Not all DAB broadcasts are able to use the

DRC function. If the broadcast does not support DRC,

then the DRC setting in the radio will have no effect.

● [Prune Invalid]: Select this option to delete all

unavailable stations from the station list.

● [System Settings]: Select this option to go to the

System settings menu and configure the radio (refer

to the chapter "Using the System settings menu" for

details).

Showing DAB information on the display

When listening to a DAB radio broadcast, repeatedly

press the Info / Menu button to cycle through the following

information on the radio's display:

Text, Program type, Multiplex name & Frequency, Date,

Bit rate, Codec & Audio type, Signal error & Strength, DL

Plus text (Some stations may provide other programme

related information for the display in addition to the

regular text. If none is available, a message "no info" is

displayed.)

If the broadcast being received is in stereo, then the stereo

speaker icon will be shown at the bottom of the radio's

display. If the currently tuned station has been stored as a

preset, then the preset number will also be shown.

If a DAB broadcast provides a slideshow image, this may

be viewed full-screen by pressing the Select button. To

exit the slideshow image, press the Select button again.

Listening to FM radio

Tuning into FM stations

To tune into FM radio stations, follow these steps:

Turn on the radio using the Standby button.

Select the FM radio mode by repeatedly pressing the

Source button.

Rotate the Tuning knob clockwise or anti-clockwise and

then press the Auto tune button to automatically tune

into an FM station with a higher or lower frequency

respectively. Your radio will stop scanning when it finds

a station of sufficient strength. The display will show

the frequency of the signal which has been found and a

signal strength icon will be shown in the bottom bar of

the radio's display to indicate the strength of the signal

received. If RDS information is available, an RDS icon

will also be shown in the bottom bar of the radio's

display and after a few seconds the display will show

the radio station name.

Rotate the Tuning knob to fine-tune the frequency with

steps of 0.05MHz if needed.

Repeat the steps 3 and 4 to tune into other radio

stations.

Adjust the Volume to the required setting.

Note:

If you find that FM reception is poor, try repositioning the

antenna.

The FM radio menu

You can open the FM radio menu by pressing and holding

the Info / Menu button while the radio is in the FM radio

mode.

Rotate the Tuning knob to select one of the options and

then press the Tuning knob to confirm your choice.

The radio's default and recommended settings are

indicated using an asterisk.

The FM radio menu offers the following options:

● [FM Scan Zone]: Select this option to configure if the

radio should only look for strong signals ("Local") or

all signals ("Distant") when using the automatic tuning

feature.

● [FM RDS]: Select this option to enable or disable RDS

reception. When listening to an FM radio station that

is also broadcasting RDS data, select [On] to enable

RDS information reception or [Off] to disable RDS

information reception.