Tecfrigo ARMONIA HOT Instalación Y Uso página 6

Operator's guide:
1. Unpacking instructions
2. Opening the protective cover
3. Cleaning the cover and external parts
I
4. Connection to the mains
5. Controls
UK
6. Checking correct operation
7. Cleaning the heated plates
D
E
!
WARNINGS
F
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
NL
1 . Adults should operate this appliance only. Do not allow children to use the controls or play with it. . It
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
P
4. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
S
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. 6
7. The manufacturers of this appliance accept no responsibility for the consequences of misuse in
DK
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice.
FIN
B
!
Our products are for internal use only – do not install outside restaurants, shops.
GR
CZ
EE
1. UNPACKING INSTRUCTIONS
1a. Cut surrounding tape . Remove the cardboard package by sliding it upwards, remove the nails from
LV
the wooden crate with care. . Lift the appliance, without putting pressure on the handgrip.
pallet or crate, thus disengaging the wheels of the appliance. . Make sure there is nothing left in the
LT
package before disposing of it. . Sort out the packaging materials in order to facilitate disposal (see
picture 1).
H
2. OPENING THE PROTECTIVE COVER
1.
Plug the machine into the power supply socket, as described in Chapter 5. . Turn the switch of the
M
electric lifting system
lamps off ten minutes before lowering the cover (see fig. 2).
PL
3. CLEANING THE COVER AND EXTERNAL PARTS
SK
1. Never use detergents containing alcohol or solvents which would irremediably damage the cover,
compromising its transparency. . Use only a soft damp sponge. . Dry with a clean cloth.
SLO
4. CONNECTION TO THE MAINS
1 . Ensure that mains voltage and frequency are the same as those stated on the rating plate
to the appliance. . Ensure that the supply socket:
rated current as set out on the rating plate; c) complies with the IEC regulations:- thermal-magnetic switch
with In = rated value as stated on the rating plate; - differential with Id sensitivity = 30 mA. . Ensure that
there is no danger of explosion (AD) in the room. . Make sure the environment is suitable for the power
supply cable provided. The cable of the appliance is H05 VVF, designed for internal use. . Insert the plug
in the socket (do not use three-way adapters and reduction adapters).(see fig. 3).
5. CONTROLS (PAG. 3 XR30CH)
The appliance is supplied with adjusting controls located in a protected panel on the front. 1. Cover
lifting switch:
internal light.
temperature.
the temperature set-point, which can be changed by pressing button
figure 4).
5
2
5
(A) to position II until the cover is fully
2
2
Position II lifting Position 0 still Position I lowering.
3. Plate switch:
to switch on the plate resisstor.
Thermostat: to adjust the plate's temperature. Press button
Operator's guide
Maintenance manual (Page 46):
1. Replacement of the lamps
2. Replacement of the cover's lifting motor
3. Wiring diagram
4
3. N.B.:
3
a) is properly earthed; b) fulfils the requirements of the
4
4. Thermometer
6
3
3. Remove the
2
turn the heated shelves and heating
(A)
3
5
2. Light switch: to switch on the
: to display the plate's
5 "SET or P" once to display
6 "UP" 7 "DOWN"
or button
2
attached
(see